Fixed I2S_STATIC stepping

Grbl_Esp32/src/I2SOut.cpp

@@ -168,7 +168,8 @@ static inline void gpio_matrix_out_check(uint8_t gpio, uint32_t signal_idx, bool
     }
 }
 
-static inline void i2s_out_single_data() {
+void i2s_out_push() {
+    if (i2s_out_pulser_status == PASSTHROUGH) {
 #if I2S_OUT_NUM_BITS == 16
         uint32_t port_data = atomic_load(&i2s_out_port_data);
         port_data <<= 16;                   // Shift needed. This specification is not spelled out in the manual.
@@ -176,6 +177,7 @@ static inline void i2s_out_single_data() {
 #else
         I2S0.conf_single_data = atomic_load(&i2s_out_port_data);  // Apply port data in real-time (static I2S)
 #endif
+    }
 }
 
 static inline void i2s_out_reset_fifo_without_lock() {
@@ -561,15 +563,6 @@ void IRAM_ATTR i2s_out_write(uint8_t pin, uint8_t val) {
     } else {
         atomic_fetch_and(&i2s_out_port_data, ~bit);
     }
-#ifdef USE_I2S_OUT_STREAM_IMPL
-    // It needs a lock for access, but I've given up because I need speed.
-    // This is not a problem as long as there is no overlap between the status change and digitalWrite().
-    if (i2s_out_pulser_status == PASSTHROUGH) {
-        i2s_out_single_data();
-    }
-#else
-    i2s_out_single_data();
-#endif
 }
 
 uint8_t IRAM_ATTR i2s_out_read(uint8_t pin) {

Grbl_Esp32/src/I2SOut.h

@@ -110,6 +110,8 @@ int i2s_out_init();
 */
 uint8_t i2s_out_read(uint8_t pin);
 
+void i2s_out_push();
+
 /*
    Set a bit in the internal pin state var. (not written electrically)
    pin: expanded pin No. (0..31)

Grbl_Esp32/src/Machine/Axes.cpp

@@ -160,6 +160,7 @@ namespace Machine {
                 a->unstep();
             }
         }
+        config->_stepping->finishPulse();
     }
 
     // Some small helpers to find the axis index and axis ganged index for a given motor. This

Grbl_Esp32/src/Pins/I2SOPinDetail.cpp

@@ -60,6 +60,7 @@ namespace Pins {
     // Write and wait for completion.  Not suitable for use from an ISR
     void I2SOPinDetail::synchronousWrite(int high) {
         write(high);
+        i2s_out_push();
         i2s_out_delay();
     }
 

Grbl_Esp32/src/Stepping.cpp

@@ -91,6 +91,7 @@ namespace Machine {
                 i2s_out_push_sample(_pulseUsecs);
                 break;
             case I2S_STATIC:
+                i2s_out_push();
             case TIMED:
                 spinDelay(_stepPulseStartTime, _pulseUsecs);
                 break;
@@ -135,6 +136,20 @@ namespace Machine {
         }
     }
 
+    void Stepping::finishPulse() {
+        switch (_engine) {
+            case stepper_id_t::I2S_STREAM:
+                break;
+            case stepper_id_t::I2S_STATIC:
+                i2s_out_push();
+                break;
+            case stepper_id_t::TIMED:
+                break;
+            case stepper_id_t::RMT:
+                break;
+        }
+    }
+
     // The argument is in units of ticks of the timer that generates ISRs
     void IRAM_ATTR Stepping::setTimerPeriod(uint16_t timerTicks) {
         if (_engine == I2S_STREAM) {

Grbl_Esp32/src/Stepping.h

@@ -74,6 +74,7 @@ namespace Machine {
         void waitPulse();      // Wait for pulse length
         void waitDirection();  // Wait for direction delay
         void waitMotion();     // Wait for motion to complete
+        void finishPulse();    // Cleanup after unstep
 
         // Timers
         void setTimerPeriod(uint16_t timerTicks);