byuu says:
New terminal is in. Much nicer to use now. Command history makes a major
difference in usability.
The SMP is now fully traceable and debuggable. Basically they act as
separate entities, you can trace both at the same time, but for the most
part running and stepping is performed on the chip you select.
I'm going to put off CPU+SMP interleave support for a while. I don't
actually think it'll be too hard. Will get trickier if/when we support
coprocessor debugging.
Remaining tasks:
- aliases
- hotkeys
- save states
- window geometry
Basically, the debugger's done. Just have to add the UI fluff.
I also removed tracing/memory export from higan. It was always meant to
be temporary until the debugger was remade.
byuu says:
Commands can be prefixed with: (cpu|smp|ppu|dsp|apu|vram|oam|cgram)/ to
set their source. Eg "vram/hex 0800" or "smp/breakpoints.append execute
ffc0"; default is cpu.
These overlap a little bit in odd ways, but that's just the way the SNES
works: it's not a very orthogonal system. CPU is both a processor and
the main bus (ROM, RAM, WRAM, etc), APU is the shared memory by the
SMP+DSP (eg use it to catch writes from either chip); PPU probably won't
ever be used since it's broken down into three separate buses (VRAM,
OAM, CGRAM), but DSP could be useful for tracking bugs like we found in
Koushien 2 with the DSP echo buffer corrupting SMP opcodes. Technically
the PPU memory pools are only ever tripped by the CPU poking at them, as
the PPU doesn't ever write.
I now have run.for, run.to, step.for, step.to. The difference is that
run only prints the next instruction after running, whereas step prints
all of the instructions along the way as well. run.to acts the same as
"step over" here. Although it's not quite as nice, since you have to
specify the address of the next instruction.
Logging the Field/Vcounter/Hcounter on instruction listings now, good
for timing information.
Added in the tracer mask, as well as memory export, as well as
VRAM/OAM/CGRAM/SMP read/write/execute breakpoints, as well as an APU
usage map (it tracks DSP reads/writes separately, although I don't
currently have debugger callbacks on DSP accesses just yet.)
Have not hooked up actual SMP debugging just yet, but I plan to soon.
Still thinking about how I want to allow / block interleaving of
instructions (terminal output and tracing.)
So ... remaining tasks at this point:
- full SMP debugging
- CPU+SMP interleave support
- aliases
- hotkeys
- save states (will be kind of tricky ... will have to suppress
breakpoints during synchronization, or abort a save in a break event.)
- keep track of window geometry between runs
byuu says:
Changelog:
- target-ethos/ is now target-higan/ (will unfortunately screw up diffs
pretty badly at this point.)
- had a serious bug in nall::optional<T>::operator=, which is now fixed.
- added tracer (no masking just yet, I need to write a nall::bitvector
class because I don't want to hard-code those anymore.)
- added usage logging (keep track of RWX/EP states for all bus
addresses.)
- added read/write to poke at memory (hex also works for reading, but
this one can poke at MMIO regs and is for one address only.)
- added both run.for (# of instructions) and run.to (program counter
address.)
- added read/write/execute breakpoints with counters for a given
address, and with an optional compare byte (for read/write modes.)
About the only major things left now for loki is support for trace
masking, memory export, and VRAM/OAM/CGRAM access.
For phoenix/Console, I really need to add a history to up+down arrows,
and I should support left/right insert-at.
