1
0
mirror of https://github.com/nophead/NopSCADlib.git synced 2025-01-16 13:08:15 +01:00
2024-06-30 14:54:02 +02:00
..
2020-03-02 13:49:41 +00:00
2023-10-30 16:25:07 +00:00
2023-10-30 09:17:50 +00:00
2023-10-30 09:17:50 +00:00
2020-12-30 19:05:14 +00:00
2023-10-30 09:17:50 +00:00
2020-12-30 19:05:14 +00:00
2023-10-30 09:17:50 +00:00
2020-12-30 19:05:14 +00:00
2023-10-30 09:17:50 +00:00
2023-10-30 09:17:50 +00:00
2020-12-30 19:05:14 +00:00
2023-10-30 09:17:50 +00:00
2023-10-30 09:17:50 +00:00
2023-10-30 09:17:50 +00:00
2023-10-30 09:17:50 +00:00
2023-10-30 09:17:50 +00:00
2021-10-02 20:45:15 +01:00
2023-10-30 09:17:50 +00:00
2020-12-30 19:05:14 +00:00
2021-10-28 12:50:22 +01:00
2021-10-02 20:45:15 +01:00

A gallery of projects made with NopSCADlib

ArduinoThermostat

Arduino thermostat to control a beer fridge to use it as an environmental chamber.

Blinder

Tasmota roller blind open / close mechanism

ClockSetter

An IOT device for programming UK wireless clocks that are out of reach of the UK MSF time signal but are on UK time, e.g. in Tenerife.

EnviroPlus

Environmental monitor using Enviro+ sensor board and a Raspberry Pi Zero.

FilamentDryBox

A small fan oven with a spool holder to keep the filament warm and dry.

HydraBot

Current state of HydraRaptor after being modified for laser engraving.

IOT 50V PSU

WiFi controllable PSU

IOT LOAD

WiFi controllable programmable load

LED Box

Indicator LEDs used to debug a Bosch diswasher problem.

Lab ATX PSU

Bench power supply built around an ATX PSU.

  • Cheap LED voltmeters show the voltage on the four main outputs.
  • The 5V standby output is available from a USB socket. The main PSU can be switched on with a switch or by pulling the green socket next to it low.
  • The green LED shows the power good signal.
  • Dummy loads keep the outputs in range.

Laser Load

15kV dummy load for testing CO2 laser PSUs

MainsBreakOutBox

13A socket break out box with 4mm jacks to measure voltage and / or load current and earth leakage current.

Intended as a simple example of NopSCADlib use. Don't build it unless you understand the safety implications of working with mains electricity. In the words of the great Paul Carlson, "if you are following along, you are doing so at your own risk".

In normal use the neutral jack sockets are linked with a short lead and so are the two earth jacks. Current can be safely measured using a clamp ammeter around the neutral link.

Voltage and current waveforms can be measured simultaneously with a Mooshimeter CAT III multimeter connected to the bottom three jacks.

Earth leakage current can be measured by connecting an AC milliampere meter between the two earth jacks. The DUT must be mounted on an insulated substrate and must not be touched while its earth is disconnected. Don't be tempted to float the earth of an oscilloscope this way, use a mains isolation transformer to power the DUT instead. Earth leakage can be measured Canadian CSA style by disconnected the neutral link from the left socket and linking the central neutral to the live.

Mains Box

Mains isolated and variable supply with metering.

MultiSwitch

Multi Tasmota switch to replace 5 Sonoffs

MultiSwitch2

Multi Tasmota switch to replace 5 Sonoffs

PSU Cover

A base and shroud to make PSU safe to sit on a desk

PSU Tube

12V power supply made in an aluminium tube for fire safety

PT_camera

Two 28BYJ_48 geared stepper motors and a Raspberry v1 camera, combined with 4 drops of superglue. Script PT_camera.scad nicely demonstrates new 2nd optional arg (motor shaft angle) of geared_stepper().

PotBox

Potentiometer box with course and fine controls and three 4mm binding posts

PowerBank

LION powerbank with e-paper charge status display

SunBot

A solar tracker to keep a solar panel pointing at the sun.

Turntable

WiFi enabled remote control turntable for photography

Was actually made from DiBond but shown made with carbon fibre here.

Variac

Motorised variac with WiFi control, see hydraraptor.blogspot.com/2018/04/esp8266-spi-spy