openscad/Mendel90
1
0
Fork 0
mirror of https://github.com/nophead/Mendel90.git synced 2025-01-17 21:08:16 +01:00
Code Issues Releases Wiki Activity
Mendel90/Settings/printrunconf.ini

30 lines
682 B
INI
Raw Normal View History

Various design improvements: The X ends now have much stronger bar clamps and the nut traps are moved to the top for less lead screw wobble. X motor bracket now has two screws in the front of the motor and one at the back allowing it to be much smaller. The Z couplings now use neoprene tubing instead of PVC and close completely. The tube end caps are now nut traps to allow the tube to just have a single hole. The rear fixing blocks now have the central screw going the other way so have onyl two nut traps. The extruder springs now have washers to increase the default tension. The spool holder now has the washers on the outside of the spool. The carriage fan bracket has been strengthened. The fan duct now has a hole to cool the top of the hot end. Small printed parts now aggregated onto one build plate. Hole in the Wade's big gear increased slightly. The heat shield is now 5 layers of cardboard instead of foil and an air gap. Bom generation and exploded view mode can now be enabled on the command line. The assembly diagrams for the manual are now built from the command line. Some mods for the Huxley version but still broken. Fixed the long ATX bracket holes ending coincident with the face. Can now have non square print beds. Cap screws now shown silver instead of black as now all BZP. Now shows the motor wire position. % operator no longer used for transparency as OpenScad behaviour has changed. Now includes the Skeinforge and Pronteface configurations on the SD card of priovided in the kit.
2013-09-25 01:28:24 +01:00
macro HOME
G28
G1X0Y0F12000
macro BL
G1 X90 Y-95 F12000
M84
macro BR
G1 X-90 Y-95 F12000
Fixed typo in Pronterface config: the BR button was not disabling the motors. Also fixed typo in end.gcode, only a problem if code for second fan was uncommented
2013-10-29 23:20:32 +00:00
M84
Various design improvements: The X ends now have much stronger bar clamps and the nut traps are moved to the top for less lead screw wobble. X motor bracket now has two screws in the front of the motor and one at the back allowing it to be much smaller. The Z couplings now use neoprene tubing instead of PVC and close completely. The tube end caps are now nut traps to allow the tube to just have a single hole. The rear fixing blocks now have the central screw going the other way so have onyl two nut traps. The extruder springs now have washers to increase the default tension. The spool holder now has the washers on the outside of the spool. The carriage fan bracket has been strengthened. The fan duct now has a hole to cool the top of the hot end. Small printed parts now aggregated onto one build plate. Hole in the Wade's big gear increased slightly. The heat shield is now 5 layers of cardboard instead of foil and an air gap. Bom generation and exploded view mode can now be enabled on the command line. The assembly diagrams for the manual are now built from the command line. Some mods for the Huxley version but still broken. Fixed the long ATX bracket holes ending coincident with the face. Can now have non square print beds. Cap screws now shown silver instead of black as now all BZP. Now shows the motor wire position. % operator no longer used for transparency as OpenScad behaviour has changed. Now includes the Skeinforge and Pronteface configurations on the SD card of priovided in the kit.
2013-09-25 01:28:24 +01:00
set xy_feedrate 50000
set z_feedrate 240
set e_feedrate 60
button 0 "HOME" /c "green" HOME
button 1 "BL" /c "blue" BL
button 2 "BM" /c "blue" G1X0Y-95
button 3 "BR" /c "blue" BR
button 4 "FL" /c "blue" G1 X90 Y90 F12000
button 5 "FM" /c "blue" G1 X0 Y90 F12000
button 6 "FR" /c "blue" G1 X-90 Y90 F12000
button 7 "ORIGIN" /c "green" G1X0Y0Z0
button 8 "FOFF" /c "yellow" M107
button 9 "FON" /c "red" M106
set last_file_path D:\dist
set build_dimensions 200x200x100-100-100+0
set port COM22
set baudrate 250000
set temperature_abs 240
set temperature_pla 220
set bedtemp_abs 130
Reference in New Issue Copy Permalink