Added pictures and documentation for extrusions.

Initial submission of E2020 aluminium extrusion.

lib.scad

@@ -62,6 +62,7 @@ include <vitamins/spools.scad>
 include <vitamins/mains_sockets.scad>
 include <vitamins/ldrs.scad>
 include <vitamins/geared_steppers.scad>
+include <vitamins/extrusions.scad>
 
 use <vitamins/jack.scad>
 use <vitamins/meter.scad>

libtest.scad

@@ -32,6 +32,7 @@ use <tests/cable_strips.scad>
 use <tests/components.scad>
 use <tests/d_connectors.scad>
 use <tests/displays.scad>
+use <tests/extrusions.scad>
 use <tests/fans.scad>
 use <tests/fuseholder.scad>
 use <tests/geared_steppers.scad>
@@ -152,7 +153,7 @@ leadnuts_y = pillars_y + 40;
 pulleys_y = leadnuts_y +40;
 hot_ends_y = pulleys_y + 60;
 linear_bearings_y = hot_ends_y + 50;
-sheets_y = linear_bearings_y + 50;
+sheets_y = linear_bearings_y + 100;
 pcbs_y = sheets_y + 40;
 displays_y = pcbs_y + 150;
 fans_y = displays_y + 100;
@@ -203,6 +204,10 @@ translate([x0, linear_bearings_y]) {
     rods();
 }
 
+translate([x0+120, linear_bearings_y+30]) {
+    extrusions();
+}
+
 translate([x0 + 10, hot_ends_y])
     hot_ends();
 

readme.md

@@ -28,24 +28,25 @@ See [usage](docs/usage.md) for requirements, installation instructions and a usa
 <tr><td> <a href = "#Components">Components</a> </td><td> <a href = "#Pulleys">Pulleys</a> </td><td> <a href = "#Fan_guard">Fan_guard</a> </td><td> <a href = "#Offset">Offset</a> </td><td></td></tr>
 <tr><td> <a href = "#D_connectors">D_connectors</a> </td><td> <a href = "#Rails">Rails</a> </td><td> <a href = "#Fixing_block">Fixing_block</a> </td><td> <a href = "#Quadrant">Quadrant</a> </td><td></td></tr>
 <tr><td> <a href = "#Displays">Displays</a> </td><td> <a href = "#Ring_terminals">Ring_terminals</a> </td><td> <a href = "#Flat_hinge">Flat_hinge</a> </td><td> <a href = "#Round">Round</a> </td><td></td></tr>
-<tr><td> <a href = "#Fans">Fans</a> </td><td> <a href = "#Rockers">Rockers</a> </td><td> <a href = "#Foot">Foot</a> </td><td> <a href = "#Rounded_cylinder">Rounded_cylinder</a> </td><td></td></tr>
-<tr><td> <a href = "#Fuseholder">Fuseholder</a> </td><td> <a href = "#Rod">Rod</a> </td><td> <a href = "#Handle">Handle</a> </td><td> <a href = "#Rounded_polygon">Rounded_polygon</a> </td><td></td></tr>
-<tr><td> <a href = "#Geared_steppers">Geared_steppers</a> </td><td> <a href = "#Screws">Screws</a> </td><td> <a href = "#Pcb_mount">Pcb_mount</a> </td><td> <a href = "#Sector">Sector</a> </td><td></td></tr>
-<tr><td> <a href = "#Green_terminals">Green_terminals</a> </td><td> <a href = "#Sealing_strip">Sealing_strip</a> </td><td> <a href = "#Psu_shroud">Psu_shroud</a> </td><td> <a href = "#Sweep">Sweep</a> </td><td></td></tr>
-<tr><td> <a href = "#Hot_ends">Hot_ends</a> </td><td> <a href = "#Sheets">Sheets</a> </td><td> <a href = "#Ribbon_clamp">Ribbon_clamp</a> </td><td> <a href = "#Tube">Tube</a> </td><td></td></tr>
-<tr><td> <a href = "#Hygrometer">Hygrometer</a> </td><td> <a href = "#Spades">Spades</a> </td><td> <a href = "#Screw_knob">Screw_knob</a> </td><td></td><td></td></tr>
-<tr><td> <a href = "#Iecs">Iecs</a> </td><td> <a href = "#Spools">Spools</a> </td><td> <a href = "#Socket_box">Socket_box</a> </td><td></td><td></td></tr>
-<tr><td> <a href = "#Inserts">Inserts</a> </td><td> <a href = "#Springs">Springs</a> </td><td> <a href = "#Ssr_shroud">Ssr_shroud</a> </td><td></td><td></td></tr>
-<tr><td> <a href = "#Jack">Jack</a> </td><td> <a href = "#Ssrs">Ssrs</a> </td><td> <a href = "#Strap_handle">Strap_handle</a> </td><td></td><td></td></tr>
-<tr><td> <a href = "#Ldrs">Ldrs</a> </td><td> <a href = "#Stepper_motors">Stepper_motors</a> </td><td></td><td></td><td></td></tr>
-<tr><td> <a href = "#Leadnuts">Leadnuts</a> </td><td> <a href = "#Toggles">Toggles</a> </td><td></td><td></td><td></td></tr>
-<tr><td> <a href = "#Leds">Leds</a> </td><td> <a href = "#Transformers">Transformers</a> </td><td></td><td></td><td></td></tr>
-<tr><td> <a href = "#Light_strips">Light_strips</a> </td><td> <a href = "#Tubings">Tubings</a> </td><td></td><td></td><td></td></tr>
-<tr><td> <a href = "#Linear_bearings">Linear_bearings</a> </td><td> <a href = "#Variacs">Variacs</a> </td><td></td><td></td><td></td></tr>
-<tr><td> <a href = "#Mains_sockets">Mains_sockets</a> </td><td> <a href = "#Veroboard">Veroboard</a> </td><td></td><td></td><td></td></tr>
-<tr><td> <a href = "#Meter">Meter</a> </td><td> <a href = "#Washers">Washers</a> </td><td></td><td></td><td></td></tr>
-<tr><td> <a href = "#Microswitches">Microswitches</a> </td><td> <a href = "#Wire">Wire</a> </td><td></td><td></td><td></td></tr>
-<tr><td> <a href = "#Microview">Microview</a> </td><td> <a href = "#Zipties">Zipties</a> </td><td></td><td></td><td></td></tr>
+<tr><td> <a href = "#Extrusions">Extrusions</a> </td><td> <a href = "#Rockers">Rockers</a> </td><td> <a href = "#Foot">Foot</a> </td><td> <a href = "#Rounded_cylinder">Rounded_cylinder</a> </td><td></td></tr>
+<tr><td> <a href = "#Fans">Fans</a> </td><td> <a href = "#Rod">Rod</a> </td><td> <a href = "#Handle">Handle</a> </td><td> <a href = "#Rounded_polygon">Rounded_polygon</a> </td><td></td></tr>
+<tr><td> <a href = "#Fuseholder">Fuseholder</a> </td><td> <a href = "#Screws">Screws</a> </td><td> <a href = "#Pcb_mount">Pcb_mount</a> </td><td> <a href = "#Sector">Sector</a> </td><td></td></tr>
+<tr><td> <a href = "#Geared_steppers">Geared_steppers</a> </td><td> <a href = "#Sealing_strip">Sealing_strip</a> </td><td> <a href = "#Psu_shroud">Psu_shroud</a> </td><td> <a href = "#Sweep">Sweep</a> </td><td></td></tr>
+<tr><td> <a href = "#Green_terminals">Green_terminals</a> </td><td> <a href = "#Sheets">Sheets</a> </td><td> <a href = "#Ribbon_clamp">Ribbon_clamp</a> </td><td> <a href = "#Tube">Tube</a> </td><td></td></tr>
+<tr><td> <a href = "#Hot_ends">Hot_ends</a> </td><td> <a href = "#Spades">Spades</a> </td><td> <a href = "#Screw_knob">Screw_knob</a> </td><td></td><td></td></tr>
+<tr><td> <a href = "#Hygrometer">Hygrometer</a> </td><td> <a href = "#Spools">Spools</a> </td><td> <a href = "#Socket_box">Socket_box</a> </td><td></td><td></td></tr>
+<tr><td> <a href = "#Iecs">Iecs</a> </td><td> <a href = "#Springs">Springs</a> </td><td> <a href = "#Ssr_shroud">Ssr_shroud</a> </td><td></td><td></td></tr>
+<tr><td> <a href = "#Inserts">Inserts</a> </td><td> <a href = "#Ssrs">Ssrs</a> </td><td> <a href = "#Strap_handle">Strap_handle</a> </td><td></td><td></td></tr>
+<tr><td> <a href = "#Jack">Jack</a> </td><td> <a href = "#Stepper_motors">Stepper_motors</a> </td><td></td><td></td><td></td></tr>
+<tr><td> <a href = "#Ldrs">Ldrs</a> </td><td> <a href = "#Toggles">Toggles</a> </td><td></td><td></td><td></td></tr>
+<tr><td> <a href = "#Leadnuts">Leadnuts</a> </td><td> <a href = "#Transformers">Transformers</a> </td><td></td><td></td><td></td></tr>
+<tr><td> <a href = "#Leds">Leds</a> </td><td> <a href = "#Tubings">Tubings</a> </td><td></td><td></td><td></td></tr>
+<tr><td> <a href = "#Light_strips">Light_strips</a> </td><td> <a href = "#Variacs">Variacs</a> </td><td></td><td></td><td></td></tr>
+<tr><td> <a href = "#Linear_bearings">Linear_bearings</a> </td><td> <a href = "#Veroboard">Veroboard</a> </td><td></td><td></td><td></td></tr>
+<tr><td> <a href = "#Mains_sockets">Mains_sockets</a> </td><td> <a href = "#Washers">Washers</a> </td><td></td><td></td><td></td></tr>
+<tr><td> <a href = "#Meter">Meter</a> </td><td> <a href = "#Wire">Wire</a> </td><td></td><td></td><td></td></tr>
+<tr><td> <a href = "#Microswitches">Microswitches</a> </td><td> <a href = "#Zipties">Zipties</a> </td><td></td><td></td><td></td></tr>
+<tr><td> <a href = "#Microview">Microview</a> </td><td></td><td></td><td></td><td></td></tr>
 <tr><td> <a href = "#Modules">Modules</a> </td><td></td><td></td><td></td><td></td></tr>
 </table>
 
@@ -585,6 +586,54 @@ LCD dispays.
 |   1 | ```display(SSD1963_4p3)``` |  LCD display SSD1963 4.3" |
 
 
+<a href="#top">Top</a>
+
+---
+<a name="Extrusions"></a>
+## Extrusions
+Aluminium  extrusion.
+
+
+[vitamins/extrusions.scad](vitamins/extrusions.scad) Object definitions.
+
+[vitamins/extrusion.scad](vitamins/extrusion.scad) Implementation.
+
+[tests/extrusions.scad](tests/extrusions.scad) Code for this example.
+
+### Properties
+| Function | Description |
+|:--- |:--- |
+| ```extrusion_center_hole(type)``` | Diameter of center hole |
+| ```extrusion_center_square(type)``` | Size of center square |
+| ```extrusion_channel_width(type)``` | Channel width |
+| ```extrusion_channel_width_internal(type)``` | Internal channel width |
+| ```extrusion_corner_hole(type)``` | Diameter of corner hole |
+| ```extrusion_fillet(type)``` | Radius of corner fillet |
+| ```extrusion_height(type)``` | Height of extrusion |
+| ```extrusion_spar_thickness(type)``` | Spar thickness |
+| ```extrusion_tab_thickness(type)``` | Tab thickness |
+| ```extrusion_width(type)``` | Width of extrusion |
+
+### Modules
+| Module | Description |
+|:--- |:--- |
+| ```extrusion(type, length, cornerHole = false)``` | Draw the specified extrusion |
+
+![extrusions](tests/png/extrusions.png)
+
+### Vitamins
+| Qty | Module call | BOM entry |
+| ---:|:--- |:---|
+|   1 | ```extrusion(E2020, 80)``` |  Extrusion E2020 x 80mm |
+|   1 | ```extrusion(E2040, 80)``` |  Extrusion E2040 x 80mm |
+|   1 | ```extrusion(E2060, 80)``` |  Extrusion E2060 x 80mm |
+|   1 | ```extrusion(E2080, 80)``` |  Extrusion E2080 x 80mm |
+|   1 | ```extrusion(E3030, 80)``` |  Extrusion E3030 x 80mm |
+|   1 | ```extrusion(E3060, 80)``` |  Extrusion E3060 x 80mm |
+|   1 | ```extrusion(E4040, 80)``` |  Extrusion E4040 x 80mm |
+|   1 | ```extrusion(E4080, 80)``` |  Extrusion E4080 x 80mm |
+
+
 <a href="#top">Top</a>
 
 ---
@@ -630,6 +679,7 @@ Can draw three styles: solid, open frame and open frame with screw bosses.
 | Qty | Module call | BOM entry |
 | ---:|:--- |:---|
 |   1 | ```fan(fan120x25)``` |  Fan 120mm x 25mm |
+|   1 | ```fan(fan17x8)``` |  Fan 17mm x 8mm |
 |   1 | ```fan(fan25x10)``` |  Fan 25mm x 10mm |
 |   1 | ```fan(fan30x10)``` |  Fan 30mm x 10mm |
 |   1 | ```fan(fan40x11)``` |  Fan 40mm x 11mm |
@@ -639,14 +689,17 @@ Can draw three styles: solid, open frame and open frame with screw bosses.
 |   1 | ```fan(fan70x15)``` |  Fan 70mm x 15mm |
 |   1 | ```fan(fan80x25)``` |  Fan 80mm x 25mm |
 |   1 | ```fan(fan80x38)``` |  Fan 80mm x 38mm |
+|   4 | ```nut(M2_nut, nyloc = true)``` |  Nut M2 x 1.6mm nyloc |
 |   4 | ```nut(M2p5_nut, nyloc = true)``` |  Nut M2.5 x 2.2mm nyloc |
 |   8 | ```nut(M3_nut, nyloc = true)``` |  Nut M3 x 2.4mm nyloc |
 |  28 | ```nut(M4_nut, nyloc = true)``` |  Nut M4 x 3.2mm nyloc |
+|   4 | ```screw(M2_cap_screw, 16)``` |  Screw M2 cap x 16mm |
 |   4 | ```screw(M2p5_pan_screw, 20)``` |  Screw M2.5 pan x 20mm |
 |   8 | ```screw(M3_dome_screw, 20)``` |  Screw M3 dome x 20mm |
 |  20 | ```screw(M4_dome_screw, 16)``` |  Screw M4 dome x 16mm |
 |   4 | ```screw(M4_dome_screw, 25)``` |  Screw M4 dome x 25mm |
 |   4 | ```screw(M4_dome_screw, 30)``` |  Screw M4 dome x 30mm |
+|   8 | ```washer(M2_washer)``` |  Washer  M2 x 5mm x 0.3mm |
 |   8 | ```washer(M2p5_washer)``` |  Washer  M2.5 x 5.9mm x 0.5mm |
 |  12 | ```washer(M3_washer)``` |  Washer  M3 x 7mm x 0.5mm |
 |  32 | ```washer(M4_washer)``` |  Washer  M4 x 9mm x 0.8mm |
@@ -825,7 +878,7 @@ Needs updating as mostly obsolete versions.
 ### Modules
 | Module | Description |
 |:--- |:--- |
-| ```hot_end(type, filament, naked = false)``` | Draw specified hot end |
+| ```hot_end(type, filament, naked = false, resistor_wire_rotate = [0,0,0])``` | Draw specified hot end |
 
 ![hot_ends](tests/png/hot_ends.png)
 
@@ -1678,8 +1731,9 @@ PCBs and perfboard with optional components. The shape can be a rectangle with o
 ### Functions
 | Function | Description |
 |:--- |:--- |
-| ```pcb_component_position(type, name)``` | Return x y position of specified component |
+| ```pcb_component_position(type, name, index = 0)``` | Return x y position of specified component |
 | ```pcb_coord(type, p)``` | Convert offsets from the edge to coordinates relative to the centre |
+| ```pcb_grid_pos(type, x, y, z = 0)``` | Returns a pcb grid position |
 | ```pcb_screw(type, cap = hs_cap)``` | Mounting screw type |
 
 ### Modules
@@ -1699,7 +1753,7 @@ PCBs and perfboard with optional components. The shape can be a rectangle with o
 | ```pcb_component_position(type, name)``` | Position child at the specified component position |
 | ```pcb_components(type, cutouts = false, angle = undef)``` | Draw list of PCB components on the PCB |
 | ```pcb_cutouts(type, angle = undef)``` | Make cut outs to clear components on a PCB |
-| ```pcb_grid(type, x, y, z = 0)``` | Positions children at specified grid positions |
+| ```pcb_grid(type, x, y, z = 0)``` | Positions children at specified grid position |
 | ```pcb_screw_positions(type)``` | Positions children at the mounting hole positions |
 | ```pcb_spacer(screw, height, wall = 1.8, taper = 0)``` | Generate STL for PCB spacer |
 | ```rj45(cutout = false)``` | Draw RJ45 Ethernet connector |
@@ -2159,7 +2213,7 @@ Ring terminals and earth assemblies for DiBond panels.
 ---
 <a name="Rockers"></a>
 ## Rockers
-Rocket switch. Also used for neon indicator in the same form factor.
+Rocker switch. Also used for neon indicator in the same form factor.
 
 
 [vitamins/rockers.scad](vitamins/rockers.scad) Object definitions.
@@ -3577,6 +3631,7 @@ The ring spacing as well as the number of spokes can be specified, if zero a gas
 | Qty | Filename |
 | ---:|:--- |
 |   1 | fan_guard_120.stl |
+|   1 | fan_guard_17.stl |
 |   1 | fan_guard_25.stl |
 |   1 | fan_guard_30.stl |
 |   1 | fan_guard_40.stl |

tests/extrusions.scad

@@ -0,0 +1,30 @@
+//
+// NopSCADlib Copyright Chris Palmer 2020
+// nop.head@gmail.com
+// hydraraptor.blogspot.com
+//
+// This file is part of NopSCADlib.
+//
+// NopSCADlib is free software: you can redistribute it and/or modify it under the terms of the
+// GNU General Public License as published by the Free Software Foundation, either version 3 of
+// the License, or (at your option) any later version.
+//
+// NopSCADlib is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;
+// without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+// See the GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License along with NopSCADlib.
+// If not, see <https://www.gnu.org/licenses/>.
+//
+include <../core.scad>
+use <../utils/layout.scad>
+
+include <../vitamins/extrusions.scad>
+
+module extrusions()
+    layout([for(e = extrusions) extrusion_width(e)], 10)
+        extrusion(extrusions[$i], 80);
+
+if ($preview)
+    extrusions();
+

vitamins/e3d.scad

@@ -61,30 +61,35 @@ heater_y = heater_width / 2;
 
 fan_x_offset = rad_dia / 2 + 4;
 
-module e3d_resistor(type) {
+module e3d_resistor(type, naked = false, resistor_wire_rotate = [0,0,0]) {
     translate([11 - heater_x, -3 - heater_y, heater_height / 2 + nozzle_h]) {
         color("grey")
             rotate([-90, 0, 0])
                 cylinder(r = resistor_dia / 2, h = resistor_len);
 
-        color("red")
-            translate([-3.5/2, resistor_len  + 3.5/2 + 1, 0]) {
-                cylinder(d = 3.5, h = 36);
+        if(!naked)
+            color("red")
+                translate([0, resistor_len + 3.5/2 + 1, 0]) {
+                rotate(resistor_wire_rotate) {
+                    translate([-3.5/2, 0, 0]) {
+                        cylinder(d = 3.5, h = 36);
 
-                translate([3.5, 0, 0])
-                    cylinder(r = 3.5 / 2, h = 36);
+                        translate([3.5, 0, 0])
+                            cylinder(r = 3.5 / 2, h = 36);
+                    }
+                }
             }
     }
 }
 
-module heater_block(type) {
+module heater_block(type, naked = false, resistor_wire_rotate = [0,0,0]) {
     translate_z(-hot_end_length(type))  {
         translate_z(nozzle_h)
             color("lightgrey")
                 translate([-heater_x, -heater_y, 0])
                     cube([heater_length, heater_width, heater_height]);
 
-        e3d_resistor(type);
+        e3d_resistor(type, naked, resistor_wire_rotate);
         e3d_nozzle(type);
     }
 }
@@ -118,7 +123,7 @@ module e3d_fan(type) {
                 fan(fan30x10);
 }
 
-module e3d_hot_end(type, filament, naked = false) {
+module e3d_hot_end(type, filament, naked = false, resistor_wire_rotate = [0,0,0]) {
     insulator_length = hot_end_insulator_length(type);
     inset = hot_end_inset(type);
     h_ailettes = rad_len / (2 * rad_nb_ailettes - 1);
@@ -146,17 +151,17 @@ module e3d_hot_end(type, filament, naked = false) {
             }
 
     rotate(90)
-        heater_block(type);
+        heater_block(type, naked, resistor_wire_rotate);
 
     if(!naked)
         translate_z(inset - insulator_length)
             e3d_fan();
 }
 
-module e3d_hot_end_assembly(type, filament, naked = false) {
+module e3d_hot_end_assembly(type, filament, naked = false, resistor_wire_rotate = [0,0,0]) {
     bundle = 3.2;
 
-    e3d_hot_end(type, filament, naked);
+    e3d_hot_end(type, filament, naked, resistor_wire_rotate);
 
     // Wire and ziptie
     if(!naked)

vitamins/extrusion.scad

@@ -0,0 +1,128 @@
+//
+// NopSCADlib Copyright Chris Palmer 2020
+// nop.head@gmail.com
+// hydraraptor.blogspot.com
+//
+// This file is part of NopSCADlib.
+//
+// NopSCADlib is free software: you can redistribute it and/or modify it under the terms of the
+// GNU General Public License as published by the Free Software Foundation, either version 3 of
+// the License, or (at your option) any later version.
+//
+// NopSCADlib is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;
+// without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+// See the GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License along with NopSCADlib.
+// If not, see <https://www.gnu.org/licenses/>.
+
+//
+//! Aluminium  extrusion.
+//
+include <../core.scad>
+
+function extrusion_width(type)          = type[1];   //! Width of extrusion
+function extrusion_height(type)         = type[2];   //! Height of extrusion
+function extrusion_center_hole(type)    = type[3];   //! Diameter of center hole
+function extrusion_corner_hole(type)    = type[4];   //! Diameter of corner hole
+function extrusion_center_square(type)  = type[5];   //! Size of center square
+function extrusion_channel_width(type)  = type[6];   //! Channel width
+function extrusion_channel_width_internal(type)  = type[7];   //! Internal channel width
+function extrusion_tab_thickness(type)  = type[8];   //! Tab thickness
+function extrusion_spar_thickness(type) = type[9];   //! Spar thickness
+function extrusion_fillet(type)         = type[10];  //! Radius of corner fillet
+
+module extrusion_cross_section(type, cornerHole) {
+
+    module extrusion_corner(type, cornerHole) {
+        width = extrusion_width(type);
+        tabThickness = extrusion_tab_thickness(type);
+        sparThickness = extrusion_spar_thickness(type);
+        centerSquare = extrusion_center_square(type);
+        channelWidth = extrusion_channel_width(type);
+        fillet = extrusion_fillet(type);
+        cornerSize = (width-channelWidth)/2;
+        cornerSquare = (width-extrusion_channel_width_internal(type))/2;
+        cornerHoleDiameter =extrusion_corner_hole(type);
+
+        translate([-width/2,-width/2]) {
+            difference() {
+                union() {
+                    translate([fillet,0])
+                        square([cornerSize-fillet,tabThickness]);
+                    translate([0,fillet])
+                        square([tabThickness,cornerSize-fillet]);
+                    translate([fillet,fillet])
+                        circle(fillet);
+                    translate([fillet,fillet])
+                        square([cornerSquare-fillet,cornerSquare-fillet]);
+                }
+                if(cornerHole)
+                    translate([cornerSquare/2,cornerSquare/2])
+                        circle(d=cornerHoleDiameter);
+            }
+        }
+        rotate(-135) translate([centerSquare/2,-sparThickness/2]) square([sqrt(2)*(width-centerSquare-cornerSquare)/2,sparThickness]);
+    }
+
+    module extrusion_center_section(type) {
+        width = extrusion_width(type);
+        tabThickness = extrusion_tab_thickness(type);
+        sparThickness = extrusion_spar_thickness(type);
+        centerSquare = extrusion_center_square(type);
+        channelWidth = extrusion_channel_width(type);
+
+        translate([0,width/2])
+            for(angle=[225,315])
+                rotate(angle)
+                    translate([centerSquare/2,-sparThickness/2])
+                        square([sqrt(2)*(width-centerSquare)/2,sparThickness]);
+        translate([0,-width/2])
+            for(angle=[45,135])
+                rotate(angle)
+                    translate([centerSquare/2,-sparThickness/2])
+                        square([sqrt(2)*(width-centerSquare)/2,sparThickness]);
+
+        centerHeight = width-channelWidth;
+        translate([-width/2,-centerHeight/2])
+            square([tabThickness,centerHeight]);
+        translate([width/2-tabThickness,-centerHeight/2])
+            square([tabThickness,centerHeight]);
+    }
+
+
+    centerSquare = extrusion_center_square(type);
+
+    width = extrusion_width(type);
+    height = extrusion_height(type);
+    count = (height-width)/width;
+
+    for(i=[0:count])
+        translate([0,i*width+(width-height)/2])
+            difference() {
+                square([centerSquare,centerSquare],center=true);
+                circle(d=extrusion_center_hole(type));
+            }
+    translate([0,(width-height)/2])
+        for(angle=[0,90])
+            rotate(angle)
+                extrusion_corner(type, cornerHole);
+    translate([0,-(width-height)/2])
+        for(angle=[180,270])
+            rotate(angle)
+                extrusion_corner(type, cornerHole);
+    if(count>=1)
+        for(i=[1:count])
+            translate([0,i*width-height/2])
+                extrusion_center_section(type);
+}
+
+module extrusion(type, length, cornerHole = false) { //! Draw the specified extrusion
+
+    vitamin(str("extrusion(", type[0], ", ", length, "): Extrusion ", type[0], " x ", length, "mm"));
+
+    color(grey90)
+        linear_extrude(height = length)
+            extrusion_cross_section(type, cornerHole);
+}
+

vitamins/extrusions.scad

@@ -0,0 +1,35 @@
+//
+// NopSCADlib Copyright Chris Palmer 2020
+// nop.head@gmail.com
+// hydraraptor.blogspot.com
+//
+// This file is part of NopSCADlib.
+//
+// NopSCADlib is free software: you can redistribute it and/or modify it under the terms of the
+// GNU General Public License as published by the Free Software Foundation, either version 3 of
+// the License, or (at your option) any later version.
+//
+// NopSCADlib is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;
+// without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+// See the GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License along with NopSCADlib.
+// If not, see <https://www.gnu.org/licenses/>.
+//
+//
+// Extrusion
+//
+//                   W   H    d1   d2   s  cw   cwi    t  st  f
+E2020  = [ "E2020", 20, 20,  4.2,   0,  8,  6, 12.0,   2,  2, 1 ];
+E2040  = [ "E2040", 20, 40,  4.2,   0,  8,  6, 12.0,   2,  2, 1 ];
+E2060  = [ "E2060", 20, 60,  4.2,   0,  8,  6, 12.0,   2,  2, 1 ];
+E2080  = [ "E2080", 20, 80,  4.2,   0,  8,  6, 12.0,   2,  2, 1 ];
+E3030  = [ "E3030", 30, 30,  6.8, 4.2, 12,  8, 16.5,   2,  2, 1 ];
+E3060  = [ "E3060", 30, 60,  6.8, 4.2, 12,  8, 16.5,   2,  2, 1 ];
+E4040  = [ "E4040", 40, 40, 10.5, 6.0, 15, 10, 20.0, 5.5,  3, 1 ];
+E4080  = [ "E4080", 40, 80, 10.5, 6.0, 15, 10, 20.0, 5.5,  3, 1 ];
+
+extrusions = [E2020,E2040,E2060,E2080,E3030,E3060,E4040,E4080];
+
+use <extrusion.scad>
+

vitamins/fans.scad

@@ -40,7 +40,8 @@ fan50x15 = [50, 15, 48, 20,    M4_dome_screw, 25,   12.5,100,7, 0,   undef];
 fan40x11 = [40, 11, 37, 16,    M3_dome_screw, 25,   7.5,100, 9, 0,   undef];
 fan30x10 = [30, 10, 27, 12,    M3_dome_screw, 17,   10, 100, 5, 0,   undef];
 fan25x10 = [25, 10, 24, 10,   M2p5_pan_screw, 16,   10, 100, 5, 0,   undef];
+fan17x8  = [17,  8, 16, 6.75,  M2_cap_screw,  12.6,  8, 100, 7, 0,   undef];
 
-fans = [fan25x10, fan30x10, fan40x11, fan50x15, fan60x15, fan60x25, fan70x15, fan80x25, fan80x38, fan120x25];
+fans = [fan17x8, fan25x10, fan30x10, fan40x11, fan50x15, fan60x15, fan60x25, fan70x15, fan80x25, fan80x38, fan120x25];
 
 use <fan.scad>

vitamins/hot_end.scad

@@ -44,10 +44,10 @@ function hot_end_length(type) = hot_end_total_length(type) - hot_end_inset(type)
 use <jhead.scad>
 use <e3d.scad>
 
-module hot_end(type, filament, naked = false) { //! Draw specified hot end
+module hot_end(type, filament, naked = false, resistor_wire_rotate = [0,0,0]) { //! Draw specified hot end
     if(hot_end_style(type) == jhead)
         jhead_hot_end_assembly(type, filament, naked);
 
     if(hot_end_style(type) == e3d)
-        e3d_hot_end_assembly(type, filament, naked);
+        e3d_hot_end_assembly(type, filament, naked, resistor_wire_rotate);
 }

vitamins/pcb.scad

@@ -49,9 +49,12 @@ function pcb_grid(type)         = type[13]; //! Grid if a perfboard
 function pcb_polygon(type)      = type[14]; //! Optional outline polygon for odd shaped boards
 function pcb_screw(type, cap = hs_cap) = Len(type[15]) ? type[15] : find_screw(cap, screw_smaller_than(pcb_hole_d(type))); //! Mounting screw type
 
-module pcb_grid(type, x, y, z = 0)  //! Positions children at specified grid positions
-    translate([-pcb_length(type) / 2 + pcb_grid(type).x + 2.54 * x,
-               -pcb_width(type)  / 2 + pcb_grid(type).y + 2.54 * y, pcb_thickness(type) + z])
+function pcb_grid_pos(type, x, y, z = 0) = //! Returns a pcb grid position
+    [-pcb_length(type) / 2 + pcb_grid(type).x + 2.54 * x,
+     -pcb_width(type)  / 2 + pcb_grid(type).y + 2.54 * y, pcb_thickness(type) + z];
+
+module pcb_grid(type, x, y, z = 0)  //! Positions children at specified grid position
+    translate(pcb_grid_pos(type, x, y, z))
         children();
 
 // allows negative ordinates to represent offsets from the far edge
@@ -730,8 +733,8 @@ module pcb_component(comp, cutouts = false, angle = undef) { //! Draw pcb compon
     }
 }
 
-function pcb_component_position(type, name) = //! Return x y position of specified component
-    [for(comp = pcb_components(type), p = [pcb_coord(type, [comp.x, comp.y])]) if(comp[3] == name) [p.x, p.y]][0];
+function pcb_component_position(type, name, index = 0) = //! Return x y position of specified component
+    [for(comp = pcb_components(type), p = [pcb_coord(type, [comp.x, comp.y])]) if(comp[3] == name) [p.x, p.y]][index];
 
 module pcb_component_position(type, name) { //! Position child at the specified component position
     for(comp = pcb_components(type)) {
@@ -807,9 +810,9 @@ module pcb(type) { //! Draw specified PCB
             pcb_screw_positions(type)
                 tube(or =  max(pcb_land_d(type), 1) / 2, ir = pcb_hole_d(type) / 2, h = t + 2 * eps);
 
-    fr4 = pcb_colour(type) == "green";
+    fr4 = pcb_colour(type) != "sienna";
     plating = 0.15;
-    color(fr4 ? "silver" : "gold")
+    color(pcb_colour(type) == "green" ? "silver" : "gold")
         translate_z(-plating)
             linear_extrude(height = fr4 ? t + 2 * plating : plating)
                 if(Len(grid)) {

vitamins/pcbs.scad

@@ -218,17 +218,19 @@ RPI0 =  ["RPI0", "Raspberry Pi Zero",     65,    30,    1.4, 3,    2.75, 6, "gre
      [12.4,  3.4,   -90, "mini_hdmi"],
      [54,    2,     -90, "usb_uA"],
      [41.4,  2,     -90, "usb_uA"],
-     [7.25,  16.7,  180, "uSD", [12, 11.5, 1.28]],
+     [7.25,  16.7,  180, "uSD", [12, 11.5, 1.4]],
      [-1.3,    15,    0, "flat_flex"],
     ],
     [": Micro SD card"],
     [32.5 - 9.5 * 2.54, 26.5 - 1.27, 20, 2]];
 
-EnviroPlus =  ["EnviroPlus", "Enviro+",     65,    30,    1.6, 3,    2.75, 6, "white", false, [[3.5, 3.5], [-3.5, 3.5], [-3.5, -3.5], [3.5, -3.5]],
-    [[32.5, -3.5,   0, "-2p54socket", 20, 2, false, 5, true],
+EnviroPlus =  ["EnviroPlus", "Enviro+",     65,    30.6,    1.6, 3,    2.75, 6, "white", false, [[3.5, 3.8], [-3.5, 3.8], [-3.5, -3.8], [3.5, -3.8]],
+    [[32.5, -3.8,   0, "-2p54socket", 20, 2, false, 5, true],
+     [-15.5, 2.5,   0, "-chip", 15, 5, 3, "white"],
+     [-14.25,16.25, 0, "chip", 27.5, 13.5, 1.5]
     ],
     [],
-    []];
+    [8, 1.5, 9, 1]];
 
 
 ArduinoUno3 = ["ArduinoUno3", "Arduino Uno R3", 68.58, 53.34, 1.6, 0, 3.3, 0, "#2140BE", false, [[15.24, 50.8],[66.04, 35.56],[66.04, 7.62],[13.97, 2.54]],

vitamins/pillars.scad

@@ -31,7 +31,7 @@
 //
 M2x16_brass_pillar     = ["M2x16_brass_pillar",     "nurled",    2, 16, 3.17,      3.17,       0, 0, brass,     brass,    3,-3];
 M3x13_hex_pillar       = ["M3x13_hex_pillar",       "hex",       3, 13, 5/cos(30), 5/cos(30),  6, 6, "silver", "silver", -6, 6];
-M3x20_hex_pillar       = ["M3x20_hex_pillar",       "hex",       3, 20, 5/cos(30), 5/cos(30),  6, 6, "silver", "silver", -6, 6];
+M3x20_hex_pillar       = ["M3x20_hex_pillar",       "hex",       3, 20, 5/cos(30), 5/cos(30),  6, 6, "silver", "silver", -8, 8];
 M3x20_nylon_pillar     = ["M3x20_nylon_pillar",     "nylon",     3, 20, 8,         5/cos(30),  0, 6, "white",   brass,   -6, 6];
 M4x17_nylon_pillar     = ["M4x17_nylon_pillar",     "nylon",     4, 20, 8,         5/cos(30),  0, 6, "white",   brass,   -6, 6];
 M3x20_nylon_hex_pillar = ["M3x20_nylon_hex_pillar", "hex nylon", 3, 20, 8/cos(30), 8/cos(30),  6, 6,  grey20,   grey20,  -6, 6];

vitamins/rocker.scad

@@ -18,7 +18,7 @@
 //
 
 //
-//! Rocket switch. Also used for neon indicator in the same form factor.
+//! Rocker switch. Also used for neon indicator in the same form factor.
 //
 include <../core.scad>
 use <spade.scad>

vitamins/screws.scad

@@ -110,7 +110,7 @@ screw_lists = [
 [ M2_cap_screw, M2p5_cap_screw, M3_cap_screw, M4_cap_screw, M5_cap_screw, M6_cap_screw, M8_cap_screw],
 [ 0,            0,              M3_low_cap_screw],
 [ 0,            0,              M3_hex_screw, M4_hex_screw, M5_hex_screw, M6_hex_screw, M8_hex_screw],
-[ 0,            M2p5_pan_screw, M3_pan_screw, M4_pan_screw, No632_pan_screw, M5_pan_screw, M6_pan_screw],
+[ 0,            M2p5_pan_screw, M3_pan_screw, M4_pan_screw, M5_pan_screw, M6_pan_screw, No632_pan_screw],
 [ 0,            No2_screw,      No4_screw,    No6_screw,    No6_cs_screw],
 [ 0,            M2_cs_cap_screw,M3_cs_cap_screw, M4_cs_cap_screw],
 [ 0,            0,              M3_dome_screw, M4_dome_screw],