Merge pull request #94 from martinbudden/carbon_tube_fix

Fix to centering of carbon fiber tubing.

lib.scad

@@ -54,6 +54,7 @@ include <vitamins/ring_terminals.scad>
 include <vitamins/rails.scad>
 include <vitamins/rod.scad>
 include <vitamins/scs_bearing_blocks.scad>
+include <vitamins/shaft_couplings.scad>
 include <vitamins/sheets.scad>
 include <vitamins/sk_brackets.scad>
 include <vitamins/spools.scad>

libtest.scad

@@ -85,6 +85,7 @@ use <tests/rod.scad>
 use <tests/screws.scad>
 use <tests/SCS_bearing_blocks.scad>
 use <tests/sealing_strip.scad>
+use <tests/shaft_couplings.scad>
 use <tests/sheets.scad>
 use <tests/SK_brackets.scad>
 use <tests/spades.scad>
@@ -429,6 +430,9 @@ translate([x4, sk_brackets_y])
 translate([x4, extrusion_brackets_y])
     extrusion_brackets();
 
+translate([x4 + 120, extrusion_brackets_y])
+    shaft_couplings();
+
 translate([x4, scs_bearing_blocks_y])
     scs_bearing_blocks();
 

readme.md

@@ -30,20 +30,21 @@ See [usage](docs/usage.md) for requirements, installation instructions and a usa
 <tr><td> <a href = "#Cable_strips">Cable_strips</a> </td><td> <a href = "#Linear_bearings">Linear_bearings</a> </td><td> <a href = "#SSRs">SSRs</a> </td><td> <a href = "#Fan_guard">Fan_guard</a> </td><td> <a href = "#Horiholes">Horiholes</a> </td><td></td></tr>
 <tr><td> <a href = "#Cameras">Cameras</a> </td><td> <a href = "#Magnets">Magnets</a> </td><td> <a href = "#Screws">Screws</a> </td><td> <a href = "#Fixing_block">Fixing_block</a> </td><td> <a href = "#Layout">Layout</a> </td><td></td></tr>
 <tr><td> <a href = "#Circlips">Circlips</a> </td><td> <a href = "#Mains_sockets">Mains_sockets</a> </td><td> <a href = "#Sealing_strip">Sealing_strip</a> </td><td> <a href = "#Flat_hinge">Flat_hinge</a> </td><td> <a href = "#Maths">Maths</a> </td><td></td></tr>
-<tr><td> <a href = "#Components">Components</a> </td><td> <a href = "#Microswitches">Microswitches</a> </td><td> <a href = "#Sheets">Sheets</a> </td><td> <a href = "#Foot">Foot</a> </td><td> <a href = "#Offset">Offset</a> </td><td></td></tr>
-<tr><td> <a href = "#DIP">DIP</a> </td><td> <a href = "#Microview">Microview</a> </td><td> <a href = "#Spades">Spades</a> </td><td> <a href = "#Handle">Handle</a> </td><td> <a href = "#Quadrant">Quadrant</a> </td><td></td></tr>
-<tr><td> <a href = "#D_connectors">D_connectors</a> </td><td> <a href = "#Modules">Modules</a> </td><td> <a href = "#Spools">Spools</a> </td><td> <a href = "#PCB_mount">PCB_mount</a> </td><td> <a href = "#Round">Round</a> </td><td></td></tr>
-<tr><td> <a href = "#Displays">Displays</a> </td><td> <a href = "#Nuts">Nuts</a> </td><td> <a href = "#Springs">Springs</a> </td><td> <a href = "#PSU_shroud">PSU_shroud</a> </td><td> <a href = "#Rounded_cylinder">Rounded_cylinder</a> </td><td></td></tr>
-<tr><td> <a href = "#Extrusion_brackets">Extrusion_brackets</a> </td><td> <a href = "#O_ring">O_ring</a> </td><td> <a href = "#Stepper_motors">Stepper_motors</a> </td><td> <a href = "#Printed_box">Printed_box</a> </td><td> <a href = "#Rounded_polygon">Rounded_polygon</a> </td><td></td></tr>
-<tr><td> <a href = "#Extrusions">Extrusions</a> </td><td> <a href = "#Opengrab">Opengrab</a> </td><td> <a href = "#Swiss_clips">Swiss_clips</a> </td><td> <a href = "#Ribbon_clamp">Ribbon_clamp</a> </td><td> <a href = "#Sector">Sector</a> </td><td></td></tr>
-<tr><td> <a href = "#Fans">Fans</a> </td><td> <a href = "#PCB">PCB</a> </td><td> <a href = "#Toggles">Toggles</a> </td><td> <a href = "#SSR_shroud">SSR_shroud</a> </td><td> <a href = "#Sweep">Sweep</a> </td><td></td></tr>
-<tr><td> <a href = "#Fuseholder">Fuseholder</a> </td><td> <a href = "#PCBs">PCBs</a> </td><td> <a href = "#Transformers">Transformers</a> </td><td> <a href = "#Screw_knob">Screw_knob</a> </td><td> <a href = "#Thread">Thread</a> </td><td></td></tr>
-<tr><td> <a href = "#Geared_steppers">Geared_steppers</a> </td><td> <a href = "#PSUs">PSUs</a> </td><td> <a href = "#Tubings">Tubings</a> </td><td> <a href = "#Socket_box">Socket_box</a> </td><td> <a href = "#Tube">Tube</a> </td><td></td></tr>
-<tr><td> <a href = "#Green_terminals">Green_terminals</a> </td><td> <a href = "#Panel_meters">Panel_meters</a> </td><td> <a href = "#Variacs">Variacs</a> </td><td> <a href = "#Strap_handle">Strap_handle</a> </td><td></td><td></td></tr>
-<tr><td> <a href = "#Hot_ends">Hot_ends</a> </td><td> <a href = "#Pillars">Pillars</a> </td><td> <a href = "#Veroboard">Veroboard</a> </td><td></td><td></td><td></td></tr>
-<tr><td> <a href = "#Hygrometer">Hygrometer</a> </td><td> <a href = "#Pin_headers">Pin_headers</a> </td><td> <a href = "#Washers">Washers</a> </td><td></td><td></td><td></td></tr>
-<tr><td> <a href = "#IECs">IECs</a> </td><td> <a href = "#Pulleys">Pulleys</a> </td><td> <a href = "#Wire">Wire</a> </td><td></td><td></td><td></td></tr>
-<tr><td> <a href = "#Inserts">Inserts</a> </td><td></td><td> <a href = "#Zipties">Zipties</a> </td><td></td><td></td><td></td></tr>
+<tr><td> <a href = "#Components">Components</a> </td><td> <a href = "#Microswitches">Microswitches</a> </td><td> <a href = "#Shaft_couplings">Shaft_couplings</a> </td><td> <a href = "#Foot">Foot</a> </td><td> <a href = "#Offset">Offset</a> </td><td></td></tr>
+<tr><td> <a href = "#DIP">DIP</a> </td><td> <a href = "#Microview">Microview</a> </td><td> <a href = "#Sheets">Sheets</a> </td><td> <a href = "#Handle">Handle</a> </td><td> <a href = "#Quadrant">Quadrant</a> </td><td></td></tr>
+<tr><td> <a href = "#D_connectors">D_connectors</a> </td><td> <a href = "#Modules">Modules</a> </td><td> <a href = "#Spades">Spades</a> </td><td> <a href = "#PCB_mount">PCB_mount</a> </td><td> <a href = "#Round">Round</a> </td><td></td></tr>
+<tr><td> <a href = "#Displays">Displays</a> </td><td> <a href = "#Nuts">Nuts</a> </td><td> <a href = "#Spools">Spools</a> </td><td> <a href = "#PSU_shroud">PSU_shroud</a> </td><td> <a href = "#Rounded_cylinder">Rounded_cylinder</a> </td><td></td></tr>
+<tr><td> <a href = "#Extrusion_brackets">Extrusion_brackets</a> </td><td> <a href = "#O_ring">O_ring</a> </td><td> <a href = "#Springs">Springs</a> </td><td> <a href = "#Printed_box">Printed_box</a> </td><td> <a href = "#Rounded_polygon">Rounded_polygon</a> </td><td></td></tr>
+<tr><td> <a href = "#Extrusions">Extrusions</a> </td><td> <a href = "#Opengrab">Opengrab</a> </td><td> <a href = "#Stepper_motors">Stepper_motors</a> </td><td> <a href = "#Ribbon_clamp">Ribbon_clamp</a> </td><td> <a href = "#Sector">Sector</a> </td><td></td></tr>
+<tr><td> <a href = "#Fans">Fans</a> </td><td> <a href = "#PCB">PCB</a> </td><td> <a href = "#Swiss_clips">Swiss_clips</a> </td><td> <a href = "#SSR_shroud">SSR_shroud</a> </td><td> <a href = "#Sweep">Sweep</a> </td><td></td></tr>
+<tr><td> <a href = "#Fuseholder">Fuseholder</a> </td><td> <a href = "#PCBs">PCBs</a> </td><td> <a href = "#Toggles">Toggles</a> </td><td> <a href = "#Screw_knob">Screw_knob</a> </td><td> <a href = "#Thread">Thread</a> </td><td></td></tr>
+<tr><td> <a href = "#Geared_steppers">Geared_steppers</a> </td><td> <a href = "#PSUs">PSUs</a> </td><td> <a href = "#Transformers">Transformers</a> </td><td> <a href = "#Socket_box">Socket_box</a> </td><td> <a href = "#Tube">Tube</a> </td><td></td></tr>
+<tr><td> <a href = "#Green_terminals">Green_terminals</a> </td><td> <a href = "#Panel_meters">Panel_meters</a> </td><td> <a href = "#Tubings">Tubings</a> </td><td> <a href = "#Strap_handle">Strap_handle</a> </td><td></td><td></td></tr>
+<tr><td> <a href = "#Hot_ends">Hot_ends</a> </td><td> <a href = "#Pillars">Pillars</a> </td><td> <a href = "#Variacs">Variacs</a> </td><td></td><td></td><td></td></tr>
+<tr><td> <a href = "#Hygrometer">Hygrometer</a> </td><td> <a href = "#Pin_headers">Pin_headers</a> </td><td> <a href = "#Veroboard">Veroboard</a> </td><td></td><td></td><td></td></tr>
+<tr><td> <a href = "#IECs">IECs</a> </td><td> <a href = "#Pulleys">Pulleys</a> </td><td> <a href = "#Washers">Washers</a> </td><td></td><td></td><td></td></tr>
+<tr><td> <a href = "#Inserts">Inserts</a> </td><td></td><td> <a href = "#Wire">Wire</a> </td><td></td><td></td><td></td></tr>
+<tr><td></td><td></td><td> <a href = "#Zipties">Zipties</a> </td><td></td><td></td><td></td></tr>
 </table>
 
 ---
@@ -1104,7 +1105,7 @@ Needs updating as mostly obsolete versions.
 ### Modules
 | Module | Description |
 |:--- |:--- |
-| ```hot_end(type, filament, naked = false, resistor_wire_rotate = [0,0,0])``` | Draw specified hot end |
+| ```hot_end(type, filament, naked = false, resistor_wire_rotate = [0,0,0], bowden = false)``` | Draw specified hot end |
 
 ![hot_ends](tests/png/hot_ends.png)
 
@@ -2642,6 +2643,7 @@ Timing belt pulleys, both toothed and plain with internal bearings for idlers.
 |   1 | ```pulley(GT2x20_toothed_idler)``` |  Pulley GT2 idler 20 teeth |
 |   1 | ```pulley(GT2x20_plain_idler)``` |  Pulley GT2 idler smooth 12mm |
 |   1 | ```pulley(GT2x16_plain_idler)``` |  Pulley GT2 idler smooth 9.63mm |
+|   1 | ```pulley(GT2x16x7_plain_idler)``` |  Pulley GT2 idler smooth 9.63mm |
 |   1 | ```pulley(GT2x20ob_pulley)``` |  Pulley GT2OB 20 teeth |
 |   1 | ```pulley(GT2x12_pulley)``` |  Pulley GT2RD 12 teeth |
 |   1 | ```pulley(GT2x20um_pulley)``` |  Pulley GT2UM 20 teeth |
@@ -3053,6 +3055,41 @@ Sealing strip from B&Q used to seal around the door of 3D printers.
 |   1 | ```sealing_strip(100)``` |  Sealing strip 10mm x 4mm x 100mm |
 
 
+<a href="#top">Top</a>
+
+---
+<a name="Shaft_couplings"></a>
+## Shaft_couplings
+Shaft couplings
+
+
+[vitamins/shaft_couplings.scad](vitamins/shaft_couplings.scad) Object definitions.
+
+[vitamins/shaft_coupling.scad](vitamins/shaft_coupling.scad) Implementation.
+
+[tests/shaft_couplings.scad](tests/shaft_couplings.scad) Code for this example.
+
+### Properties
+| Function | Description |
+|:--- |:--- |
+| ```sc_diameter(type)``` | Coupling outer diameter |
+| ```sc_diameter1(type)``` | Diameter of smaller shaft |
+| ```sc_diameter2(type)``` | Diameter of larger shaft |
+| ```sc_length(type)``` | Coupling length |
+
+### Modules
+| Module | Description |
+|:--- |:--- |
+| ```shaft_coupling(type, colour = "silver")``` | Draw the shaft coupling |
+
+![shaft_couplings](tests/png/shaft_couplings.png)
+
+### Vitamins
+| Qty | Module call | BOM entry |
+| ---:|:--- |:---|
+|   1 | ```shaft_coupling(SC_5x8_rigid)``` |  Shaft coupling SC_5x8_rigid |
+
+
 <a href="#top">Top</a>
 
 ---
@@ -3652,6 +3689,7 @@ Tubing and sleeving. The internal diameter can be forced to stretch it over some
 ### Vitamins
 | Qty | Module call | BOM entry |
 | ---:|:--- |:---|
+|   1 | ```tubing(CBNFIB10)``` |  Carbon fiber OD 10mm ID 8mm x 15mm |
 |   1 | ```tubing(HSHRNK16)``` |  Heatshrink sleeving ID 1.6mm x 15mm |
 |   1 | ```tubing(HSHRNK100)``` |  Heatshrink sleeving ID 10mm x 15mm |
 |   1 | ```tubing(HSHRNK24)``` |  Heatshrink sleeving ID 2.4mm x 15mm |
@@ -5740,6 +5778,7 @@ Simple tube or ring
 |:--- |:--- |
 | ```ring(or, ir)``` | Create a ring with specified external and internal radii |
 | ```tube(or, ir, h, center = true)``` | Create a tube with specified external and internal radii and height ```h``` |
+| ```woven_tube(or, ir, h, center= true, colour = grey(30)``` | Create a woven tube with specified external and internal radii, height ```h```, colours, warp and weft |
 
 ![tube](tests/png/tube.png)
 

tests/hot_ends.scad

@@ -25,7 +25,7 @@ module hot_ends()
     layout([for(h = hot_ends) 40])
         translate([-20, 0])
             rotate(90)
-                hot_end(hot_ends[$i], 3);
+                hot_end(hot_ends[$i], 3, bowden = $i == 3);
 
 if($preview)
     hot_ends();

tests/shaft_couplings.scad

@@ -0,0 +1,30 @@
+//
+// NopSCADlib Copyright Chris Palmer 2018
+// nop.head@gmail.com
+// hydraraptor.blogspot.com
+//
+// This file is part of NopSCADlib.
+//
+// NopSCADlib is free software: you can redistribute it and/or modify it under the terms of the
+// GNU General Public License as published by the Free Software Foundation, either version 3 of
+// the License, or (at your option) any later version.
+//
+// NopSCADlib is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;
+// without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+// See the GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License along with NopSCADlib.
+// If not, see <https://www.gnu.org/licenses/>.
+//
+include <../core.scad>
+include <../vitamins/shaft_couplings.scad>
+
+use <../utils/layout.scad>
+
+module shaft_couplings()
+    layout([for(s = shaft_couplings) sc_diameter(s)],5)
+        shaft_coupling(shaft_couplings[$i]);
+
+if($preview)
+    shaft_couplings();
+

tests/tubings.scad

@@ -22,7 +22,7 @@ use <../utils/layout.scad>
 include <../vitamins/tubings.scad>
 
 module tubings()
-    layout([for(t = tubings) tubing_od(t)], 10)
+    layout([for(t = tubings) tubing_od(t)], 8)
         tubing(tubings[$i]);
 
 if($preview)

utils/tube.scad

@@ -31,3 +31,41 @@ module ring(or, ir) //! Create a ring with specified external and internal radii
 module tube(or, ir, h, center = true) //! Create a tube with specified external and internal radii and height ```h```
     linear_extrude(h, center = center, convexity = 5)
         ring(or, ir);
+
+module woven_tube(or, ir, h, center= true, colour = grey(30), colour2, warp = 2, weft) {//! Create a woven tube with specified external and internal radii, height ```h```, colours, warp and weft
+    colour2 = colour2 ? colour2 : colour * 0.8;
+    weft = weft ? weft : warp;
+    warp_count = max(floor(PI * or / warp), 0.5);
+    angle = 360 / (2 * warp_count);
+
+    module layer(weft) {
+        points = [[ir, weft / 2], [or, weft / 2], [or, -weft / 2], [ir, -weft / 2]];
+        color(colour)
+            for (i = [0 : warp_count])
+                rotate(2 * i * angle)
+                    rotate_extrude(angle = angle)
+                        polygon(points);
+        color(colour2)
+            for (i = [0 : warp_count])
+                rotate((2 * i + 1) * angle)
+                    rotate_extrude(angle = angle)
+                        polygon(points);
+    }
+
+    translate_z(center ? -h / 2 : 0) {
+        weft_count = floor(h / weft);
+        if (weft_count > 0)
+            for (i = [0 : weft_count - 1]) {
+                translate_z(i * weft + weft / 2)
+                    rotate(i * angle)
+                        layer(weft);
+        }
+        remainder = h - weft * weft_count;
+        if (remainder) {
+            translate_z(weft_count * weft + remainder / 2)
+                rotate(weft_count * angle)
+                    layer(remainder);
+        }
+    }
+}
+

vitamins/e3d.scad

@@ -26,6 +26,8 @@ include <tubings.scad>
 include <zipties.scad>
 include <fans.scad>
 
+use <../utils/rounded_cylinder.scad>
+use <../utils/thread.scad>
 use <../utils/tube.scad>
 
 rad_dia = 22; // Diam of the part with ailettes
@@ -94,7 +96,34 @@ module heater_block(type, naked = false, resistor_wire_rotate = [0,0,0]) {
     }
 }
 
+module bowden_connector(cap_colour = grey(20)) {
+    ir = 4.25 / 2;
+    body_colour = silver;
 
+    color(body_colour) {
+        translate_z(-4.5) {
+            tube(or = 2.5, ir = ir, h = 4.5, center = false);
+            male_metric_thread(6, metric_coarse_pitch(5), length = 4.5, center = false, solid = false, colour = body_colour);
+        }
+        tube(or = 7.7 / 2, ir = ir, h = 2, center = false);
+        translate_z(2)
+            linear_extrude(6.5)
+                difference() {
+                    circle(d = 11.55, $fn = 6);
+                    circle(r = ir);
+                }
+        translate_z(8.5)
+            rounded_cylinder(r = 9.8 / 2, h = 2, r2 = 1.5, ir = ir);
+        translate_z(10.5)
+            tube(or = 3.5, ir = ir, h = 0.5, center = false);
+    }
+    color(cap_colour) {
+        translate_z(11)
+            tube(or = 3, ir = ir, h = 1, center = false);
+        translate_z(12)
+            tube(or = 5.5, ir = ir, h = 1.75, center = false);
+    }
+}
 
 module e3d_fan_duct(type) {
     color("DeepSkyBlue")
@@ -123,7 +152,7 @@ module e3d_fan(type) {
                 fan(fan30x10);
 }
 
-module e3d_hot_end(type, filament, naked = false, resistor_wire_rotate = [0,0,0]) {
+module e3d_hot_end(type, filament, naked = false, resistor_wire_rotate = [0,0,0], bowden = false) {
     insulator_length = hot_end_insulator_length(type);
     inset = hot_end_inset(type);
     h_ailettes = rad_len / (2 * rad_nb_ailettes - 1);
@@ -150,6 +179,10 @@ module e3d_hot_end(type, filament, naked = false, resistor_wire_rotate = [0,0,0]
                         square([100, hot_end_groove(type)]);
             }
 
+    if(bowden)
+        translate_z(inset)
+            bowden_connector();
+
     rotate(90)
         heater_block(type, naked, resistor_wire_rotate);
 
@@ -158,10 +191,10 @@ module e3d_hot_end(type, filament, naked = false, resistor_wire_rotate = [0,0,0]
             e3d_fan();
 }
 
-module e3d_hot_end_assembly(type, filament, naked = false, resistor_wire_rotate = [0,0,0]) {
+module e3d_hot_end_assembly(type, filament, naked = false, resistor_wire_rotate = [0,0,0], bowden = false) {
     bundle = 3.2;
 
-    e3d_hot_end(type, filament, naked, resistor_wire_rotate);
+    e3d_hot_end(type, filament, naked, resistor_wire_rotate, bowden);
 
     // Wire and ziptie
     if(!naked)

vitamins/hot_end.scad

@@ -44,10 +44,10 @@ function hot_end_length(type) = hot_end_total_length(type) - hot_end_inset(type)
 use <jhead.scad>
 use <e3d.scad>
 
-module hot_end(type, filament, naked = false, resistor_wire_rotate = [0,0,0]) { //! Draw specified hot end
+module hot_end(type, filament, naked = false, resistor_wire_rotate = [0,0,0], bowden = false) { //! Draw specified hot end
     if(hot_end_style(type) == jhead)
         jhead_hot_end_assembly(type, filament, naked);
 
     if(hot_end_style(type) == e3d)
-        e3d_hot_end_assembly(type, filament, naked, resistor_wire_rotate);
+        e3d_hot_end_assembly(type, filament, naked, resistor_wire_rotate, bowden);
 }

vitamins/pulleys.scad

@@ -35,7 +35,8 @@ GT2x12_pulley        = ["GT2x12_pulley",        "GT2RD", 12,  7.15, GT2x6,  6.5,
 GT2x20_toothed_idler = ["GT2x20_toothed_idler", "GT2",   20, 12.22, GT2x6,  6.5,  18, 0,   4, 18.0, 1.0, 0, 0,    false,         0];
 GT2x20_plain_idler   = ["GT2x20_plain_idler",   "GT2",    0, 12.0,  GT2x6,  6.5,  18, 0,   4, 18.0, 1.0, 0, 0,    false,         0];
 GT2x16_toothed_idler = ["GT2x16_toothed_idler", "GT2",   16,  9.75, GT2x6,  6.5,  14, 0,   3, 14.0, 1.0, 0, 0,    false,         0];
-GT2x16_plain_idler   = ["GT2x16_plain_idler",   "GT2",    0,  9.63, GT2x6,  7.0,  13, 0,   3, 13.0, 1.0, 0, 0,    false,         0];
+GT2x16_plain_idler   = ["GT2x16_plain_idler",   "GT2",    0,  9.63, GT2x6,  6.5,  13, 0,   3, 13.0, 1.0, 0, 0,    false,         0];
+GT2x16x7_plain_idler = ["GT2x16x7_plain_idler", "GT2",    0,  9.63, GT2x6,  7.0,  13, 0,   3, 13.0, 1.0, 0, 0,    false,         0];
 
 pulleys = [T5x10_pulley,
            T2p5x16_pulley,
@@ -45,6 +46,7 @@ pulleys = [T5x10_pulley,
            GT2x20_toothed_idler,
            GT2x20_plain_idler,
            GT2x16_toothed_idler,
-           GT2x16_plain_idler];
+           GT2x16_plain_idler,
+           GT2x16x7_plain_idler];
 
 use <pulley.scad>

vitamins/shaft_coupling.scad

@@ -0,0 +1,65 @@
+//
+// NopSCADlib Copyright Chris Palmer 2020
+// nop.head@gmail.com
+// hydraraptor.blogspot.com
+//
+// This file is part of NopSCADlib.
+//
+// NopSCADlib is free software: you can redistribute it and/or modify it under the terms of the
+// GNU General Public License as published by the Free Software Foundation, either version 3 of
+// the License, or (at your option) any later version.
+//
+// NopSCADlib is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;
+// without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+// See the GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License along with NopSCADlib.
+// If not, see <https://www.gnu.org/licenses/>.
+
+//
+//! Shaft couplings
+//
+include <../core.scad>
+use <../utils/tube.scad>
+
+function sc_length(type)       = type[1]; //! Coupling length
+function sc_diameter(type)     = type[2]; //! Coupling outer diameter
+function sc_diameter1(type)    = type[3]; //! Diameter of smaller shaft
+function sc_diameter2(type)    = type[4]; //! Diameter of larger shaft
+
+module shaft_coupling(type, colour = "silver") { //! Draw the shaft coupling
+    vitamin(str("shaft_coupling(", type[0], "): Shaft coupling ", type[0]));
+
+    length = sc_length(type);
+    radius = sc_diameter(type) / 2;
+    r1 = sc_diameter1(type) / 2;
+    r2 = sc_diameter2(type) / 2;
+
+    grub_length = 3;
+    module grub_screw_positions() {
+        grub_offset_z = 5;
+        for(z = [-length / 2 + grub_offset_z, length / 2 - grub_offset_z])
+            translate_z(z)
+                for(a = [0, 90])
+                    rotate([-90, 0, a])
+                        translate_z(radius + 1)
+                            children();
+    }
+
+    color(colour) {
+        render(convexity=2) difference() {
+            union() {
+                translate_z(-length / 2)
+                    tube(radius, r1, length / 2, false);
+
+                tube(radius, r2, length / 2, false);
+            }
+            grub_screw_positions()
+                rotate([180, 0, 0])
+                    cylinder(r = screw_radius(M3_grub_screw), h = 5);
+        }
+    }
+
+    grub_screw_positions()
+        not_on_bom() screw(M3_grub_screw, grub_length);
+}

vitamins/shaft_couplings.scad

@@ -0,0 +1,29 @@
+//
+// NopSCADlib Copyright Chris Palmer 2020
+// nop.head@gmail.com
+// hydraraptor.blogspot.com
+//
+// This file is part of NopSCADlib.
+//
+// NopSCADlib is free software: you can redistribute it and/or modify it under the terms of the
+// GNU General Public License as published by the Free Software Foundation, either version 3 of
+// the License, or (at your option) any later version.
+//
+// NopSCADlib is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;
+// without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+// See the GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License along with NopSCADlib.
+// If not, see <https://www.gnu.org/licenses/>.
+//
+
+//
+//! Shaft couplings
+//
+
+//                                   L   D        d1   d2
+SC_5x8_rigid  = [ "SC_5x8_rigid",    25, 12.5,    5,   8 ];
+
+shaft_couplings = [SC_5x8_rigid];
+
+use <shaft_coupling.scad>

vitamins/tubing.scad

@@ -21,6 +21,7 @@
 //! Tubing and sleeving. The internal diameter can be forced to stretch it over something.
 //
 include <../utils/core/core.scad>
+include <../utils/tube.scad>
 
 function tubing_material(type) = type[1]; //! Material description
 function tubing_od(type)       = type[2]; //! Outside diameter
@@ -38,10 +39,15 @@ module tubing(type, length = 15, forced_id = 0, center = true) { //! Draw specif
         vitamin(str("tubing(", type[0], arg(length, 15), "): ", tubing_material(type), " ID ", original_id, "mm x ",length, "mm"));
     else
         vitamin(str("tubing(", type[0], arg(length, 15), "): ", tubing_material(type), " OD ", original_od, "mm ID ", original_id,"mm x ",length, "mm"));
-    color(tubing_colour(type))
-        linear_extrude(length, center = center, convexity = 4)
-            difference() {
-                circle(d = od);
-                circle(d = id);
-            }
+
+    if(tubing_material(type) == "Carbon fiber")
+        woven_tube(od / 2, id /2, center = center, length, colour = tubing_colour(type));
+    else
+        color(tubing_colour(type))
+            linear_extrude(length, center = center, convexity = 4)
+                difference() {
+                    circle(d = od);
+                    circle(d = id);
+                }
 }
+

vitamins/tubings.scad

@@ -19,22 +19,23 @@
 
 //
 // Tubing and sleeving
-//
-PVC64     = ["PVC64",     "PVC aquarium tubing", 6,        4, [0.8, 0.8, 0.8, 0.75 ]];
-PVC85     = ["PVC85",     "PVC aquarium tubing", 8,        5, [0.8, 0.8, 0.8, 0.75 ]];
-NEOP85    = ["NEOP85",    "Neoprene tubing",     8,        5, [0.2,0.2,0.2]];
-PTFE07    = ["PTFE07",    "PTFE sleeving",       1.2,   0.71, [0.95, 0.95, 0.95, 0.9]];
-PTFE20    = ["PTFE20",    "PTFE sleeving",       2.6,      2, [0.95, 0.95, 0.95, 0.9]];
-PTFE2_4   = ["PTFE2_4",   "PTFE tubing",         4,        2, [0.95, 0.95, 0.95, 0.9]];
-PTFE2_3   = ["PTFE2_3",   "PTFE tubing",         3,        2, [0.95, 0.95, 0.95, 0.9]];
-PTFE4_6   = ["PTFE4_6",   "PTFE tubing",         6,        4, [0.95, 0.95, 0.95, 0.9]];
-PF7       = ["PF7",       "PTFE tubing",         46/10, 3.84, [0.95, 0.95, 0.95, 0.9]];
-HSHRNK16  = ["HSHRNK16",  "Heatshrink sleeving", 2.0,    1.6, "grey"];
-HSHRNK24  = ["HSHRNK24",  "Heatshrink sleeving", 2.8,    2.4, "grey"];
-HSHRNK32  = ["HSHRNK32",  "Heatshrink sleeving", 3.6,    3.2, "grey"];
-HSHRNK64  = ["HSHRNK64",  "Heatshrink sleeving", 6.8,    6.4, "grey"];
-HSHRNK100 = ["HSHRNK100", "Heatshrink sleeving",10.4,   10.0,  [0.2,0.2,0.2]];
+//                            Description           OD        ID  Colour
+PVC64         = ["PVC64",     "PVC aquarium tubing", 6,        4, [0.8, 0.8, 0.8, 0.75 ]];
+PVC85         = ["PVC85",     "PVC aquarium tubing", 8,        5, [0.8, 0.8, 0.8, 0.75 ]];
+NEOP85        = ["NEOP85",    "Neoprene tubing",     8,        5, [0.2,0.2,0.2]];
+PTFE07        = ["PTFE07",    "PTFE sleeving",       1.2,   0.71, [0.95, 0.95, 0.95, 0.9]];
+PTFE20        = ["PTFE20",    "PTFE sleeving",       2.6,      2, [0.95, 0.95, 0.95, 0.9]];
+PTFE2_4       = ["PTFE2_4",   "PTFE tubing",         4,        2, [0.95, 0.95, 0.95, 0.9]];
+PTFE2_3       = ["PTFE2_3",   "PTFE tubing",         3,        2, [0.95, 0.95, 0.95, 0.9]];
+PTFE4_6       = ["PTFE4_6",   "PTFE tubing",         6,        4, [0.95, 0.95, 0.95, 0.9]];
+PF7           = ["PF7",       "PTFE tubing",         46/10, 3.84, [0.95, 0.95, 0.95, 0.9]];
+HSHRNK16      = ["HSHRNK16",  "Heatshrink sleeving", 2.0,    1.6, "grey"];
+HSHRNK24      = ["HSHRNK24",  "Heatshrink sleeving", 2.8,    2.4, "grey"];
+HSHRNK32      = ["HSHRNK32",  "Heatshrink sleeving", 3.6,    3.2, "grey"];
+HSHRNK64      = ["HSHRNK64",  "Heatshrink sleeving", 6.8,    6.4, "grey"];
+HSHRNK100     = ["HSHRNK100", "Heatshrink sleeving",10.4,   10.0,  [0.2,0.2,0.2]];
+CARBONFIBER10 = ["CBNFIB10",  "Carbon fiber",       10.0,    8.0,  [0.3,0.3,0.3]];
 
-tubings = [PVC64, PVC85, NEOP85, PTFE07, PTFE20, PF7, PTFE2_3, PTFE2_4, PTFE4_6, HSHRNK16, HSHRNK24, HSHRNK64, HSHRNK100];
+tubings = [PVC64, PVC85, NEOP85, PTFE07, PTFE20, PF7, PTFE2_3, PTFE2_4, PTFE4_6, HSHRNK16, HSHRNK24, HSHRNK64, HSHRNK100, CARBONFIBER10];
 
 use <tubing.scad>