Fixed typo in insert name.

Belt gap position is now relative to the pitch line.
Added belt_pitch_to_back().

lib.scad

@@ -43,6 +43,7 @@ include <vitamins/ldrs.scad>
 include <vitamins/leadnuts.scad>
 include <vitamins/led_meter.scad>
 include <vitamins/light_strips.scad>
+include <vitamins/magnets.scad>
 include <vitamins/mains_sockets.scad>
 include <vitamins/modules.scad>
 include <vitamins/panel_meters.scad>

libtest.scad

@@ -50,6 +50,7 @@ use <tests/LEDs.scad>
 use <tests/light_strips.scad>
 use <tests/linear_bearings.scad>
 use <tests/LED_meters.scad>
+use <tests/magnets.scad>
 use <tests/microswitches.scad>
 use <tests/modules.scad>
 use <tests/nuts.scad>
@@ -271,8 +272,9 @@ translate([x1, leadnuts_y])
 
 leds_y = 0;
 carriers_y = leds_y + 40;
-spades_y = carriers_y + 40;
-buttons_y = spades_y + 40;
+magnets_y = carriers_y + 40;
+spades_y = magnets_y + 20;
+buttons_y = spades_y + 20;
 jacks_y = buttons_y + 40;
 microswitches_y = jacks_y + 40;
 rockers_y = microswitches_y + 40;
@@ -288,6 +290,9 @@ translate([x2 + 35, leds_y])
 translate([x2 + 8, carriers_y])
     carriers();
 
+translate([x2, magnets_y])
+    magnets();
+
 translate([x2 + 20, carriers_y])
     led_meters();
 

readme.md

@@ -26,21 +26,21 @@ See [usage](docs/usage.md) for requirements, installation instructions and a usa
 <tr><td> <a href = "#Bulldogs">Bulldogs</a> </td><td> <a href = "#Leadnuts">Leadnuts</a> </td><td> <a href = "#SK_brackets">SK_brackets</a> </td><td> <a href = "#Door_hinge">Door_hinge</a> </td><td> <a href = "#Hanging_hole">Hanging_hole</a> </td><td> <a href = "#Sphere">Sphere</a> </td></tr>
 <tr><td> <a href = "#Buttons">Buttons</a> </td><td> <a href = "#Light_strips">Light_strips</a> </td><td> <a href = "#SMDs">SMDs</a> </td><td> <a href = "#Door_latch">Door_latch</a> </td><td> <a href = "#Horiholes">Horiholes</a> </td><td> <a href = "#Teardrops">Teardrops</a> </td></tr>
 <tr><td> <a href = "#Cable_strips">Cable_strips</a> </td><td> <a href = "#Linear_bearings">Linear_bearings</a> </td><td> <a href = "#SSRs">SSRs</a> </td><td> <a href = "#Fan_guard">Fan_guard</a> </td><td> <a href = "#Layout">Layout</a> </td><td></td></tr>
-<tr><td> <a href = "#Cameras">Cameras</a> </td><td> <a href = "#Mains_sockets">Mains_sockets</a> </td><td> <a href = "#Screws">Screws</a> </td><td> <a href = "#Fixing_block">Fixing_block</a> </td><td> <a href = "#Maths">Maths</a> </td><td></td></tr>
-<tr><td> <a href = "#Circlips">Circlips</a> </td><td> <a href = "#Microswitches">Microswitches</a> </td><td> <a href = "#Sealing_strip">Sealing_strip</a> </td><td> <a href = "#Flat_hinge">Flat_hinge</a> </td><td> <a href = "#Offset">Offset</a> </td><td></td></tr>
-<tr><td> <a href = "#Components">Components</a> </td><td> <a href = "#Microview">Microview</a> </td><td> <a href = "#Sheets">Sheets</a> </td><td> <a href = "#Foot">Foot</a> </td><td> <a href = "#Quadrant">Quadrant</a> </td><td></td></tr>
-<tr><td> <a href = "#DIP">DIP</a> </td><td> <a href = "#Modules">Modules</a> </td><td> <a href = "#Spades">Spades</a> </td><td> <a href = "#Handle">Handle</a> </td><td> <a href = "#Round">Round</a> </td><td></td></tr>
-<tr><td> <a href = "#D_connectors">D_connectors</a> </td><td> <a href = "#Nuts">Nuts</a> </td><td> <a href = "#Spools">Spools</a> </td><td> <a href = "#PCB_mount">PCB_mount</a> </td><td> <a href = "#Rounded_cylinder">Rounded_cylinder</a> </td><td></td></tr>
-<tr><td> <a href = "#Displays">Displays</a> </td><td> <a href = "#O_ring">O_ring</a> </td><td> <a href = "#Springs">Springs</a> </td><td> <a href = "#PSU_shroud">PSU_shroud</a> </td><td> <a href = "#Rounded_polygon">Rounded_polygon</a> </td><td></td></tr>
-<tr><td> <a href = "#Extrusion_brackets">Extrusion_brackets</a> </td><td> <a href = "#Opengrab">Opengrab</a> </td><td> <a href = "#Stepper_motors">Stepper_motors</a> </td><td> <a href = "#Printed_box">Printed_box</a> </td><td> <a href = "#Sector">Sector</a> </td><td></td></tr>
-<tr><td> <a href = "#Extrusions">Extrusions</a> </td><td> <a href = "#PCB">PCB</a> </td><td> <a href = "#Swiss_clips">Swiss_clips</a> </td><td> <a href = "#Ribbon_clamp">Ribbon_clamp</a> </td><td> <a href = "#Sweep">Sweep</a> </td><td></td></tr>
-<tr><td> <a href = "#Fans">Fans</a> </td><td> <a href = "#PCBs">PCBs</a> </td><td> <a href = "#Toggles">Toggles</a> </td><td> <a href = "#SSR_shroud">SSR_shroud</a> </td><td> <a href = "#Thread">Thread</a> </td><td></td></tr>
-<tr><td> <a href = "#Fuseholder">Fuseholder</a> </td><td> <a href = "#PSUs">PSUs</a> </td><td> <a href = "#Transformers">Transformers</a> </td><td> <a href = "#Screw_knob">Screw_knob</a> </td><td> <a href = "#Tube">Tube</a> </td><td></td></tr>
-<tr><td> <a href = "#Geared_steppers">Geared_steppers</a> </td><td> <a href = "#Panel_meters">Panel_meters</a> </td><td> <a href = "#Tubings">Tubings</a> </td><td> <a href = "#Socket_box">Socket_box</a> </td><td></td><td></td></tr>
-<tr><td> <a href = "#Green_terminals">Green_terminals</a> </td><td> <a href = "#Pillars">Pillars</a> </td><td> <a href = "#Variacs">Variacs</a> </td><td> <a href = "#Strap_handle">Strap_handle</a> </td><td></td><td></td></tr>
-<tr><td> <a href = "#Hot_ends">Hot_ends</a> </td><td> <a href = "#Pin_headers">Pin_headers</a> </td><td> <a href = "#Veroboard">Veroboard</a> </td><td></td><td></td><td></td></tr>
-<tr><td> <a href = "#Hygrometer">Hygrometer</a> </td><td> <a href = "#Pulleys">Pulleys</a> </td><td> <a href = "#Washers">Washers</a> </td><td></td><td></td><td></td></tr>
-<tr><td> <a href = "#IECs">IECs</a> </td><td></td><td> <a href = "#Wire">Wire</a> </td><td></td><td></td><td></td></tr>
+<tr><td> <a href = "#Cameras">Cameras</a> </td><td> <a href = "#Magnets">Magnets</a> </td><td> <a href = "#Screws">Screws</a> </td><td> <a href = "#Fixing_block">Fixing_block</a> </td><td> <a href = "#Maths">Maths</a> </td><td></td></tr>
+<tr><td> <a href = "#Circlips">Circlips</a> </td><td> <a href = "#Mains_sockets">Mains_sockets</a> </td><td> <a href = "#Sealing_strip">Sealing_strip</a> </td><td> <a href = "#Flat_hinge">Flat_hinge</a> </td><td> <a href = "#Offset">Offset</a> </td><td></td></tr>
+<tr><td> <a href = "#Components">Components</a> </td><td> <a href = "#Microswitches">Microswitches</a> </td><td> <a href = "#Sheets">Sheets</a> </td><td> <a href = "#Foot">Foot</a> </td><td> <a href = "#Quadrant">Quadrant</a> </td><td></td></tr>
+<tr><td> <a href = "#DIP">DIP</a> </td><td> <a href = "#Microview">Microview</a> </td><td> <a href = "#Spades">Spades</a> </td><td> <a href = "#Handle">Handle</a> </td><td> <a href = "#Round">Round</a> </td><td></td></tr>
+<tr><td> <a href = "#D_connectors">D_connectors</a> </td><td> <a href = "#Modules">Modules</a> </td><td> <a href = "#Spools">Spools</a> </td><td> <a href = "#PCB_mount">PCB_mount</a> </td><td> <a href = "#Rounded_cylinder">Rounded_cylinder</a> </td><td></td></tr>
+<tr><td> <a href = "#Displays">Displays</a> </td><td> <a href = "#Nuts">Nuts</a> </td><td> <a href = "#Springs">Springs</a> </td><td> <a href = "#PSU_shroud">PSU_shroud</a> </td><td> <a href = "#Rounded_polygon">Rounded_polygon</a> </td><td></td></tr>
+<tr><td> <a href = "#Extrusion_brackets">Extrusion_brackets</a> </td><td> <a href = "#O_ring">O_ring</a> </td><td> <a href = "#Stepper_motors">Stepper_motors</a> </td><td> <a href = "#Printed_box">Printed_box</a> </td><td> <a href = "#Sector">Sector</a> </td><td></td></tr>
+<tr><td> <a href = "#Extrusions">Extrusions</a> </td><td> <a href = "#Opengrab">Opengrab</a> </td><td> <a href = "#Swiss_clips">Swiss_clips</a> </td><td> <a href = "#Ribbon_clamp">Ribbon_clamp</a> </td><td> <a href = "#Sweep">Sweep</a> </td><td></td></tr>
+<tr><td> <a href = "#Fans">Fans</a> </td><td> <a href = "#PCB">PCB</a> </td><td> <a href = "#Toggles">Toggles</a> </td><td> <a href = "#SSR_shroud">SSR_shroud</a> </td><td> <a href = "#Thread">Thread</a> </td><td></td></tr>
+<tr><td> <a href = "#Fuseholder">Fuseholder</a> </td><td> <a href = "#PCBs">PCBs</a> </td><td> <a href = "#Transformers">Transformers</a> </td><td> <a href = "#Screw_knob">Screw_knob</a> </td><td> <a href = "#Tube">Tube</a> </td><td></td></tr>
+<tr><td> <a href = "#Geared_steppers">Geared_steppers</a> </td><td> <a href = "#PSUs">PSUs</a> </td><td> <a href = "#Tubings">Tubings</a> </td><td> <a href = "#Socket_box">Socket_box</a> </td><td></td><td></td></tr>
+<tr><td> <a href = "#Green_terminals">Green_terminals</a> </td><td> <a href = "#Panel_meters">Panel_meters</a> </td><td> <a href = "#Variacs">Variacs</a> </td><td> <a href = "#Strap_handle">Strap_handle</a> </td><td></td><td></td></tr>
+<tr><td> <a href = "#Hot_ends">Hot_ends</a> </td><td> <a href = "#Pillars">Pillars</a> </td><td> <a href = "#Veroboard">Veroboard</a> </td><td></td><td></td><td></td></tr>
+<tr><td> <a href = "#Hygrometer">Hygrometer</a> </td><td> <a href = "#Pin_headers">Pin_headers</a> </td><td> <a href = "#Washers">Washers</a> </td><td></td><td></td><td></td></tr>
+<tr><td> <a href = "#IECs">IECs</a> </td><td> <a href = "#Pulleys">Pulleys</a> </td><td> <a href = "#Wire">Wire</a> </td><td></td><td></td><td></td></tr>
 <tr><td> <a href = "#Inserts">Inserts</a> </td><td></td><td> <a href = "#Zipties">Zipties</a> </td><td></td><td></td><td></td></tr>
 </table>
 
@@ -85,6 +85,7 @@ Axial components for PCBs.
 |   1 | ```ax_res(res1_4, 47000)``` |  Resistor 47000 Ohms 5% 0.25W |
 |   1 | ```ax_res(res1_2, 8200)``` |  Resistor 8200 Ohms 5% 0.5W |
 |   1 | ```ax_res(res1_2, 8250, tol = 1)``` |  Resistor 8250 Ohms 1% 0.5W |
+|   1 | ```wire_link(0.8, 10.16)``` |  Wire link 0.8mm x 0.4" |
 
 
 <a href="#top">Top</a>
@@ -209,6 +210,7 @@ Only models 2D paths, so not core XY!
 To make the back of the belt run against a smooth pulley on the outside of the loop specify a negative pitch radius.
 
 By default the path is a closed loop but a gap length and position can be specified to make open loops.
+To draw the gap its XY position is specified by ```gap_pos```. ```gap_pos.z``` can be used to specify a rotation if the gap is not at the bottom of the loop.
 
 Individual teeth are not drawn, instead they are represented by a lighter colour.
 
@@ -223,6 +225,7 @@ Individual teeth are not drawn, instead they are represented by a lighter colour
 | Function | Description |
 |:--- |:--- |
 | ```belt_pitch(type)``` | Pitch in mm |
+| ```belt_pitch_height(type)``` | Offset of the pitch radius from the tips of the teeth |
 | ```belt_thickness(type)``` | Total thickness including teeth |
 | ```belt_tooth_height(type)``` | Tooth height |
 | ```belt_width(type)``` | Width in mm |
@@ -231,12 +234,12 @@ Individual teeth are not drawn, instead they are represented by a lighter colour
 | Function | Description |
 |:--- |:--- |
 | ```belt_length(points, gap = 0)``` | Compute belt length given path and optional gap |
-| ```belt_pitch_height(type)``` | Offset of the pitch radius from the tips of the teeth |
+| ```belt_pitch_to_back(type)``` | Offset of the back from the pitch radius |
 
 ### Modules
 | Module | Description |
 |:--- |:--- |
-| ```belt(type, points, gap = 0, gap_pt = undef, belt_colour = grey(20)``` | Draw a belt path given a set of points and pitch radii where the pulleys are. Closed loop unless a gap is specified |
+| ```belt(type, points, gap = 0, gap_pos = undef, belt_colour = grey(20)``` | Draw a belt path given a set of points and pitch radii where the pulleys are. Closed loop unless a gap is specified |
 
 ![belts](tests/png/belts.png)
 
@@ -244,7 +247,7 @@ Individual teeth are not drawn, instead they are represented by a lighter colour
 | Qty | Module call | BOM entry |
 | ---:|:--- |:---|
 |   1 | ```belt(GT2x6, [ ... ])``` |  Belt GT2 x 6mm x 128mm |
-|   1 | ```belt(GT2x6, [ ... ], 80, [0, 0.81])``` |  Belt GT2 x 6mm x 694mm |
+|   1 | ```belt(GT2x6, [ ... ], 80, [0, 0])``` |  Belt GT2 x 6mm x 696mm |
 |   1 | ```belt(T2p5x6, [ ... ])``` |  Belt T2.5 x 6mm x 130mm |
 |   1 | ```belt(T5x10, [ ... ])``` |  Belt T5 x 10mm x 130mm |
 |   1 | ```belt(T5x6, [ ... ])``` |  Belt T5 x 6mm x 130mm |
@@ -900,7 +903,7 @@ Can draw three styles: solid, open frame and open frame with screw bosses.
 | ---:|:--- |:---|
 |   1 | ```fan(fan120x25)``` |  Fan 120mm x 25mm |
 |   1 | ```fan(fan17x8)``` |  Fan 17mm x 8mm |
-|   1 | ```fan(fan25x10)``` |  Fan 25mm x 10mm |
+|   1 | ```fan(fan25.4x10)``` |  Fan 25.4mm x 10mm |
 |   1 | ```fan(fan30x10)``` |  Fan 30mm x 10mm |
 |   1 | ```fan(fan40x11)``` |  Fan 40mm x 11mm |
 |   1 | ```fan(fan50x15)``` |  Fan 50mm x 15mm |
@@ -1250,6 +1253,7 @@ Heatfit threaded inserts. Can be pushed into thermoplastics using a soldering ir
 | Function | Description |
 |:--- |:--- |
 | ```insert_boss_radius(type, wall)``` | Compute the outer radius of an insert boss |
+| ```insert_nose_length(type, d)``` | The length before the second ring. |
 
 ### Modules
 | Module | Description |
@@ -1264,7 +1268,7 @@ Heatfit threaded inserts. Can be pushed into thermoplastics using a soldering ir
 ### Vitamins
 | Qty | Module call | BOM entry |
 | ---:|:--- |:---|
-|   1 | ```insert(F1BM)``` |  Heatfit insert M2 |
+|   1 | ```insert(F1BM2)``` |  Heatfit insert M2 |
 |   1 | ```insert(F1BM2p5)``` |  Heatfit insert M2.5 |
 |   1 | ```insert(F1BM3)``` |  Heatfit insert M3 |
 |   1 | ```insert(F1BM4)``` |  Heatfit insert M4 |
@@ -1673,6 +1677,36 @@ LMnUU linear bearings.
 |   1 | ```linear_bearing(LM8UU)``` |  Linear bearing LM8UU |
 
 
+<a href="#top">Top</a>
+
+---
+<a name="Magnets"></a>
+## Magnets
+Cylindrical and ring magnets.
+
+
+[vitamins/magnets.scad](vitamins/magnets.scad) Object definitions.
+
+[vitamins/magnet.scad](vitamins/magnet.scad) Implementation.
+
+[tests/magnets.scad](tests/magnets.scad) Code for this example.
+
+### Properties
+| Function | Description |
+|:--- |:--- |
+| ```magnet_h(type)``` | Height |
+| ```magnet_id(type)``` | Inside diameter if a ring |
+| ```magnet_od(type)``` | Outer diameter |
+| ```magnet_r(type)``` | Corner radius |
+
+### Modules
+| Module | Description |
+|:--- |:--- |
+| ```magnet(type)``` | Draw specified magnet |
+
+![magnets](tests/png/magnets.png)
+
+
 <a href="#top">Top</a>
 
 ---
@@ -2190,6 +2224,8 @@ PCBs and perfboard with optional components. The shape can be a rectangle with o
 |   2 | ```green_terminal(gt_3p5, 4)``` |  Terminal block 4 way 3.5mm |
 |   1 | ```terminal_35(4)``` |  Terminal block 4 way 3.5mm |
 |   1 | ```pcb(TestPCB)``` |  Test PCB |
+|   1 | ```wire_link(0.8, 5.08, h = 10.16)``` |  Wire link 0.8mm x 0.2" |
+|   1 | ```wire_link(0.8, 10.16)``` |  Wire link 0.8mm x 0.4" |
 
 
 <a href="#top">Top</a>
@@ -4253,7 +4289,7 @@ Star washers can be omitted by setting ```star_washers``` to false.
 ### Vitamins
 | Qty | Module call | BOM entry |
 | ---:|:--- |:---|
-|   3 | ```insert(F1BM)``` |  Heatfit insert M2 |
+|   3 | ```insert(F1BM2)``` |  Heatfit insert M2 |
 |   3 | ```insert(F1BM2p5)``` |  Heatfit insert M2.5 |
 |   3 | ```insert(F1BM3)``` |  Heatfit insert M3 |
 |   3 | ```insert(F1BM4)``` |  Heatfit insert M4 |
@@ -4415,7 +4451,7 @@ The ring spacing as well as the number of spokes can be specified, if zero a gas
 | ---:|:--- |
 |   1 | fan_guard_120.stl |
 |   1 | fan_guard_17.stl |
-|   1 | fan_guard_25.stl |
+|   1 | fan_guard_25.4.stl |
 |   1 | fan_guard_30.stl |
 |   1 | fan_guard_40.stl |
 |   1 | fan_guard_50.stl |
@@ -4473,7 +4509,7 @@ Star washers can be omitted by setting ```star_washers``` to false.
 ### Vitamins
 | Qty | Module call | BOM entry |
 | ---:|:--- |:---|
-|   3 | ```insert(F1BM)``` |  Heatfit insert M2 |
+|   3 | ```insert(F1BM2)``` |  Heatfit insert M2 |
 |   3 | ```insert(F1BM2p5)``` |  Heatfit insert M2.5 |
 |   3 | ```insert(F1BM3)``` |  Heatfit insert M3 |
 |   3 | ```insert(F1BM4)``` |  Heatfit insert M4 |
@@ -4803,7 +4839,7 @@ It can also have printed feet on the base with the screws doubling up to hold th
 ### Vitamins
 | Qty | Module call | BOM entry |
 | ---:|:--- |:---|
-|   4 | ```insert(F1BM)``` |  Heatfit insert M2 |
+|   4 | ```insert(F1BM2)``` |  Heatfit insert M2 |
 |   4 | ```insert(F1BM3)``` |  Heatfit insert M3 |
 |   4 | ```screw(M2_cap_screw, 6)``` |  Screw M2 cap x  6mm |
 |   3 | ```screw(M3_pan_screw, 6)``` |  Screw M3 pan x  6mm |
@@ -5765,6 +5801,7 @@ Global constants, functions and modules. This file is used directly or indirectl
 | ```inch(x)``` | Inch to mm conversion (For fractional inches, 'inch(1 + 7/8)' will work as expected.) |
 | ```m(x)``` | m to mm conversion |
 | ```mm(x)``` | Explicit mm specified |
+| ```no_point(str)``` | Replace decimal point in string with 'p' |
 | ```r2sides(r)``` | Replicates the OpenSCAD logic to calculate the number of sides from the radius |
 | ```r2sides4n(r)``` | Round up the number of sides to a multiple of 4 to ensure points land on all axes |
 | ```sqr(x)``` | Returns the square of ```x``` |

tests/PCB.scad

@@ -86,10 +86,13 @@ test_pcb = ["TestPCB", "Test PCB",
         [  5, 218, 180, "hdmi"],
         [  3, 235, 180, "mini_hdmi"],
         [  6, 175, 180, "uSD", [12, 11.5, 1.4]],
+
+        [ 65,   9,   0, "link", inch(0.4)],
         [ 65,  12,   0, "ax_res", res1_8, 1000],
         [ 65,  17,   0, "ax_res", res1_4, 10000],
         [ 65,  22,   0, "ax_res", res1_2, 100000],
 
+        [ 80,   9,   0, "link", inch(0.2), inch(0.4)],
         [ 80,  12,   0, "ax_res", res1_8, 1000000, 1, inch(0.1)],
         [ 80,  17,   0, "ax_res", res1_4, 100,     2, inch(0.1)],
         [ 80,  22,   0, "ax_res", res1_2, 10,     10, inch(0.2)],

tests/belts.scad

@@ -60,7 +60,7 @@ module belt_test() {
              [p4.x, p4.y, pulley_pr(GT2x20ob_pulley)]
            ];
     belt = GT2x6;
-    belt(belt, path, 80, [0,  belt_pitch_height(belt) - belt_thickness(belt) / 2]);
+    belt(belt, path, 80, [0,  0]);
 
     translate([-25, 0])
         layout([for(b = belts) belt_width(b)], 10)

tests/magnets.scad

@@ -0,0 +1,29 @@
+//
+// NopSCADlib Copyright Chris Palmer 2020
+// nop.head@gmail.com
+// hydraraptor.blogspot.com
+//
+// This file is part of NopSCADlib.
+//
+// NopSCADlib is free software: you can redistribute it and/or modify it under the terms of the
+// GNU General Public License as published by the Free Software Foundation, either version 3 of
+// the License, or (at your option) any later version.
+//
+// NopSCADlib is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;
+// without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+// See the GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License along with NopSCADlib.
+// If not, see <https://www.gnu.org/licenses/>.
+//
+include <../core.scad>
+use <../utils/layout.scad>
+
+include <../vitamins/magnets.scad>
+
+module magnets()
+    layout([for(m = magnets) magnet_od(m)], 5)
+        magnet(magnets[$i]);
+
+if($preview)
+    magnets();

utils/core/global.scad

@@ -31,6 +31,7 @@ function m(x)    = x * 1000.0;
 
 function sqr(x) = x * x;                                                            //! Returns the square of ```x```
 function echoit(x) = echo(x) x;                                                     //! Echo expression and return it, useful for debugging
+function no_point(str) = chr([for(c = str(str)) if(c == ".") ord("p") else ord(c)]);//! Replace decimal point in string with 'p'
 function in(list, x) = !!len([for(v = list) if(v == x) true]);                      //! Returns true if ```x``` is an element in the ```list```
 function Len(x) = is_list(x) ? len(x) : 0;                                          //! Returns the length of a list or 0 if ```x``` is not a list
 function r2sides(r) = $fn ? $fn : ceil(max(min(360/ $fa, r * 2 * PI / $fs), 5));    //! Replicates the OpenSCAD logic to calculate the number of sides from the radius

utils/hanging_hole.scad

@@ -39,11 +39,13 @@ module hanging_hole(z, ir, h = 100, h2 = 100) { //! Hole radius ```ir``` hanging
     infill_angle = z % (2 * layer_height) ? -45 : 45;
     below = min(z + eps, h2);
     big = 1000;
-
     render(convexity = 3) translate_z(z)
         union() {
             translate_z(2 * layer_height)
-                polyhole(ir - eps, h - 2 * layer_height);
+                if(sides(ir) > 4)
+                    polyhole(ir - eps, h - 2 * layer_height);
+                else
+                    poly_cylinder(ir, h - 2 * layer_height);
 
             difference() {
                 translate_z(-below)

utils/quadrant.scad

@@ -23,18 +23,21 @@
 include <../utils/core/core.scad>
 
 module quadrant(w, r, center = false) { //! Draw a square with one rounded corner, can be centered on the arc centre, when ```center``` is ```true```.
-    offset = center ? r - w : 0;
-    translate([offset, offset])
+    h = is_list(w) ? w.y : w;
+    w = is_list(w) ? w.x : w;
+    offset_w = center ? r - w : 0;
+    offset_h = center ? r - h : 0;
+    translate([offset_w, offset_h])
         hull() {
             intersection() {
-                translate([w - r, w - r])
+                translate([w - r, h - r])
                     circle4n(r);
 
-                square(w);
+                square([w, h]);
             }
 
             square([w, eps]);
 
-            square([eps, w]);
+            square([eps, h]);
         }
 }

vitamins/axial.scad

@@ -24,6 +24,7 @@ include <../utils/core/core.scad>
 include <../utils/round.scad>
 
 module wire_link(d, l, h = 1, tail = 3) { //! Draw a wire jumper link.
+    vitamin(str("wire_link(", d, ", ", l, arg(h, 1, "h"), arg(tail, 3, "tail"),  "): Wire link ", d, "mm x ", l / inch(1), "\""));
     r = d;
     $fn = 32;
 
@@ -57,13 +58,16 @@ module orientate_axial(length, height, pitch, wire_d) { // Orient horizontal or
     min_pitch = ceil((length + 1) / inch(0.1)) * inch(0.1);
     lead_pitch = pitch ? pitch : min_pitch;
     if(lead_pitch >= min_pitch) {
-        wire_link(wire_d, lead_pitch, height);
+        not_on_bom()
+            wire_link(wire_d, lead_pitch, height);
+
         translate_z(height)
             rotate([0, 90, 0])
                 children();
     }
     else {
-        wire_link(wire_d, lead_pitch, length + 0.7 + wire_d);
+        not_on_bom()
+            wire_link(wire_d, lead_pitch, length + 0.7 + wire_d);
 
         translate([-pitch / 2, 0, length / 2 + 0.2])
             children();

vitamins/belt.scad

@@ -24,29 +24,31 @@
 //! To make the back of the belt run against a smooth pulley on the outside of the loop specify a negative pitch radius.
 //!
 //! By default the path is a closed loop but a gap length and position can be specified to make open loops.
+//! To draw the gap its XY position is specified by ```gap_pos```. ```gap_pos.z``` can be used to specify a rotation if the gap is not at the bottom of the loop.
 //!
 //! Individual teeth are not drawn, instead they are represented by a lighter colour.
 //
 include <../utils/core/core.scad>
 use <../utils/rounded_polygon.scad>
+use <../utils/maths.scad>
 
 function belt_pitch(type)        = type[1]; //! Pitch in mm
 function belt_width(type)        = type[2]; //! Width in mm
 function belt_thickness(type)    = type[3]; //! Total thickness including teeth
 function belt_tooth_height(type) = type[4]; //! Tooth height
-function belt_pitch_height(type) = belt_tooth_height(type) + type[4]; //! Offset of the pitch radius from the tips of the teeth
+function belt_pitch_height(type) = type[5] + belt_tooth_height(type); //! Offset of the pitch radius from the tips of the teeth
 
-function no_point(str) = chr([for(c = str) if(c == ".") ord("p") else ord(c)]);
+function belt_pitch_to_back(type) = belt_thickness(type) - belt_pitch_height(type); //! Offset of the back from the pitch radius
 //
 // We model the belt path at the pitch radius of the pulleys and the pitch line of the belt to get an accurate length.
 // The belt is then drawn by offseting each side from the pitch line.
 //
-module belt(type, points, gap = 0, gap_pt = undef, belt_colour = grey(20), tooth_colour = grey(50)) { //! Draw a belt path given a set of points and pitch radii where the pulleys are. Closed loop unless a gap is specified
+module belt(type, points, gap = 0, gap_pos = undef, belt_colour = grey(20), tooth_colour = grey(50)) { //! Draw a belt path given a set of points and pitch radii where the pulleys are. Closed loop unless a gap is specified
     width = belt_width(type);
     pitch = belt_pitch(type);
     thickness = belt_thickness(type);
     part = str(type[0],pitch);
-    vitamin(str("belt(", no_point(part), "x", width, ", ", points, arg(gap, 0), arg(gap_pt, undef), "): Belt ", part," x ", width, "mm x ", length, "mm"));
+    vitamin(str("belt(", no_point(part), "x", width, ", ", points, arg(gap, 0), arg(gap_pos, undef), "): Belt ", part," x ", width, "mm x ", length, "mm"));
 
     len = len(points);
 
@@ -56,24 +58,28 @@ module belt(type, points, gap = 0, gap_pt = undef, belt_colour = grey(20), tooth
 
     module shape() rounded_polygon(points, tangents);
 
+    ph = belt_pitch_height(type);
+    th = belt_tooth_height(type);
     module gap()
         if(gap)
-            translate(gap_pt)
-                square([gap, thickness + eps], center = true);
+            translate([gap_pos.x, gap_pos.y])
+                rotate(is_undef(gap_pos.z) ? 0 : gap_pos.z)
+                    translate([0, ph - thickness / 2])
+                        square([gap, thickness + eps], center = true);
 
     color(belt_colour)
         linear_extrude(width, center = true)
             difference() {
-                offset(thickness - belt_pitch_height(type)) shape();
-                offset(-belt_pitch_height(type) + belt_tooth_height(type)) shape();
+                offset(-ph + thickness ) shape();
+                offset(-ph + th) shape();
                 gap();
-
             }
+
     color(tooth_colour)
         linear_extrude(width, center = true)
             difference() {
-                offset(-belt_pitch_height(type) + belt_tooth_height(type)) shape();
-                offset(-belt_pitch_height(type)) shape();
+                offset(-ph + th) shape();
+                offset(-ph) shape();
                 gap();
             }
 }

vitamins/fans.scad

@@ -17,28 +17,28 @@
 // If not, see <https://www.gnu.org/licenses/>.
 //
 
-//          w   d   b   h      s              h     t    o   b  b    a
-//          i   e   o   o      c              u     h    u   l  o    p
-//          d   p   r   l      r              b     i    t   a  s    p
-//          t   t   e   e      e                    c    e   d  s    e
-//          h   h              w              d     k    r   e       r
-//                      p                     i     n        s  d    t
-//                      i                     a     e    d           u
-//                      t                           s    i           r
-//                      c                           s    a           e
-//                      h
+//          w     d   b   h      s              h     t    o   b  b    a
+//          i     e   o   o      c              u     h    u   l  o    p
+//          d     p   r   l      r              b     i    t   a  s    p
+//          t     t   e   e      e                    c    e   d  s    e
+//          h     h              w              d     k    r   e       r
+//                        p                     i     n        s  d    t
+//                        i                     a     e    d           u
+//                        t                           s    i           r
+//                        c                           s    a           e
+//                        h
 //
-fan120x25= [120,25, 116,52.5,  M4_dome_screw, 41,   4,  140, 9, 0,   137];
-fan80x38 = [80, 38, 75, 35.75, M4_dome_screw, 40,   4.3, 84, 7, 0,   85];
-fan80x25 = [80, 25, 75, 35.75, M4_dome_screw, 40,   4.3, 84, 7, 0,   85];
-fan70x15 = [70, 15, 66, 30.75, M4_dome_screw, 29,   3.8, 70 ,7, 0,   undef];
-fan60x25 = [60, 25, 57, 25,    M4_dome_screw, 31.5, 3.6, 64, 7, 0,   63];
-fan60x15 = [60, 15, 57, 25,    M4_dome_screw, 29,   2.4, 60, 7, 7.7, 63];
-fan50x15 = [50, 15, 48, 20,    M4_dome_screw, 25,   12.5,100,7, 0,   undef];
-fan40x11 = [40, 11, 37, 16,    M3_dome_screw, 25,   7.5,100, 9, 0,   undef];
-fan30x10 = [30, 10, 27, 12,    M3_dome_screw, 17,   10, 100, 5, 0,   undef];
-fan25x10 = [25, 10, 24, 10,   M2p5_pan_screw, 16,   10, 100, 5, 0,   undef];
-fan17x8  = [17,  8, 16, 6.75,  M2_cap_screw,  12.6,  8, 100, 7, 0,   undef];
+fan120x25= [120, 25, 116,52.5,  M4_dome_screw, 41,   4,  140, 9, 0,   137];
+fan80x38 = [80,  38, 75, 35.75, M4_dome_screw, 40,   4.3, 84, 7, 0,   85];
+fan80x25 = [80,  25, 75, 35.75, M4_dome_screw, 40,   4.3, 84, 7, 0,   85];
+fan70x15 = [70,  15, 66, 30.75, M4_dome_screw, 29,   3.8, 70 ,7, 0,   undef];
+fan60x25 = [60,  25, 57, 25,    M4_dome_screw, 31.5, 3.6, 64, 7, 0,   63];
+fan60x15 = [60,  15, 57, 25,    M4_dome_screw, 29,   2.4, 60, 7, 7.7, 63];
+fan50x15 = [50,  15, 48, 20,    M4_dome_screw, 25,  12.5,100, 7, 0,   undef];
+fan40x11 = [40,  11, 37, 16,    M3_dome_screw, 25,   7.5,100, 9, 0,   undef];
+fan30x10 = [30,  10, 27, 12,    M3_dome_screw, 17,   10, 100, 5, 0,   undef];
+fan25x10 = [25.4,10, 24, 10,   M2p5_pan_screw, 16,   10, 100, 5, 0,   undef];
+fan17x8  = [17,   8, 16, 6.75,  M2_cap_screw,  12.6,  8, 100, 7, 0,   undef];
 
 fans = [fan17x8, fan25x10, fan30x10, fan40x11, fan50x15, fan60x15, fan60x25, fan70x15, fan80x25, fan80x38, fan120x25];
 

vitamins/hot_ends.scad

@@ -33,8 +33,7 @@
 //                                                                                       h      t     s   t              t     t
 //                                                                                              h
 //
-JHeadMk4  = ["JHeadMk4",  jhead, "JHead MK4",           64,  5.1, 16,    50, grey(20),     12,    4.64, 14, [0, 2.94, -5], 20,   20];
-JHeadMk5  = ["JHeadMk5",  jhead, "JHead MK5",         51.2,  5.1, 16,    40, grey(20),     12,    4.64, 13, [0, 2.38, -5], 20,   20];
+JHeadMk5  = ["JHeadMk5",  jhead, "JHead MK5",         51.2,  4.75,16,    40, grey(20),   12,    4.64, 13, [0, 2.38, -5], 20,   20];
 E3Dv5     = ["E3Dv5",     e3d,   "E3D V5 direct",       70,  3.7, 16,  50.1, "silver",   12,    6,    15, [1, 5,  -4.5], 14.5, 28];
 E3Dv6     = ["E3Dv6",     e3d,   "E3D V6 direct",       62,  3.7, 16,  42.7, "silver",   12,    6,    15, [1, 5,  -4.5], 14,   21];
 E3D_clone = ["E3D_clone", e3d,   "E3D clone aliexpress",66,  6.8, 16,    46, "silver",   12,    5.6,  15, [1, 5,  -4.5], 14.5, 21];

vitamins/insert.scad

@@ -24,17 +24,26 @@ include <../utils/core/core.scad>
 use <../utils/quadrant.scad>
 use <../utils/thread.scad>
 
-function insert_length(type)         = type[1]; //! Length
-function insert_outer_d(type)        = type[2]; //! Outer diameter at the top
+function insert_length(type)         = type[1];     //! Length
+function insert_outer_d(type)        = type[2];     //! Outer diameter at the top
 function insert_hole_radius(type)    = type[3] / 2; //! Radius of the required hole in the plastic
-function insert_screw_diameter(type) = type[4]; //! Screw size
-function insert_barrel_d(type)       = type[5]; //! Diameter of the main barrel
-function insert_ring1_h(type)        = type[6]; //! Height of the top and middle rings
-function insert_ring2_d(type)        = type[7]; //! Diameter of the middle ring
-function insert_ring3_d(type)        = type[8]; //! Diameter of the bottom ring
+function insert_screw_diameter(type) = type[4];     //! Screw size
+function insert_barrel_d(type)       = type[5];     //! Diameter of the main barrel
+function insert_ring1_h(type)        = type[6];     //! Height of the top and middle rings
+function insert_ring2_d(type)        = type[7];     //! Diameter of the middle ring
+function insert_ring3_d(type)        = type[8];     //! Diameter of the bottom ring
 
 function insert_hole_length(type) = round_to_layer(insert_length(type));
 
+function insert_nose_length(type, d) = let( //! The length before the second ring.
+        length = insert_length(type),
+        ring1_h = insert_ring1_h(type),
+        chamfer1 = (insert_ring2_d(type) - insert_barrel_d(type)) / 2,
+        chamfer2 = (insert_ring3_d(type) - insert_barrel_d(type)) / 2,
+        ring2_h = ring1_h + chamfer1,
+        gap = (length - ring1_h - ring2_h - chamfer2) / 3
+    ) ring1_h + gap + ring2_h - d + insert_barrel_d(type);
+
 module insert(type) { //! Draw specified insert
     length = insert_length(type);
     ring1_h = insert_ring1_h(type);
@@ -42,12 +51,12 @@ module insert(type) { //! Draw specified insert
     chamfer1 = (insert_ring2_d(type) - insert_barrel_d(type)) / 2;
     chamfer2 = (insert_ring3_d(type) - insert_barrel_d(type)) / 2;
     ring2_h = ring1_h + chamfer1;
-    gap = (length - ring1_h - ring2_h- chamfer2) / 3;
+    gap = (length - ring1_h - ring2_h - chamfer2) / 3;
 
     vitamin(str("insert(", type[0], "): Heatfit insert M", insert_screw_diameter(type)));
     $fn = 64;
     thread_d = insert_screw_diameter(type);
-    explode(20, offset =[0, 0, -5]) translate_z(eps) vflip() {
+    explode(20, offset = [0, 0, -5]) translate_z(eps) vflip() {
         r1 = thread_d / 2;
         r2 = insert_barrel_d(type) / 2;
         r3 = insert_ring3_d(type) / 2;
@@ -58,7 +67,7 @@ module insert(type) { //! Draw specified insert
         h3 = ring1_h + gap + ring2_h;
         h4 = ring1_h + gap + ring2_h + gap;
         color(brass)
-            rotate_extrude()
+            rotate_extrude(convexity = 3)
                 polygon([
                     [r1, 0],
                     [r1, length],

vitamins/inserts.scad

@@ -29,7 +29,7 @@
 //                          d         d          h    d    d
 //                                         d
 //
-F1BM2   = [ "F1BM",    4.0, 3.6, 3.2, 2,   3.0,  1.0, 3.4, 3.1 ];
+F1BM2   = [ "F1BM2",    4.0, 3.6, 3.2, 2,   3.0,  1.0, 3.4, 3.1 ];
 F1BM2p5 = [ "F1BM2p5", 5.8, 4.6, 4.0, 2.5, 3.65, 1.6, 4.4, 3.9 ];
 F1BM3   = [ "F1BM3",   5.8, 4.6, 4.0, 3,   3.65, 1.6, 4.4, 3.9 ];
 F1BM4   = [ "F1BM4",   8.2, 6.3, 5.6, 4,   5.15, 2.3, 6.0, 5.55 ];

vitamins/jhead.scad

@@ -29,7 +29,6 @@ include <zipties.scad>
 use <wire.scad>
 use <../utils/tube.scad>
 
-MK4_heater = [ 12.76, 15.88, 8.22, (15.88 / 2 - 4.5), (12.76 / 2 - 0.5 - 2.5 / 2),  (-15.88 / 2 + 5), 9.5, 3];
 MK5_heater = [ 12.76, 12.76, 8.22, (12.76 / 2 - 3.75), (12.76 / 2 - 0.5 - 2.5 / 2), (-12.76 / 2 + 4), 8,   2];
 
 function heater_width(type)  = type[0];
@@ -71,7 +70,7 @@ module heater_block(type, resistor, thermistor) {
         cone_start_r = nozzle_cone(type) / 2;
         straight = 1;
         nozzle_r = 0.4 / 2;
-        translate_z(-h / 2) vflip()
+        translate([nozzle_x(type), 0, -h / 2]) vflip()
             rotate_extrude()
                 polygon([
                     [nozzle_r,     0],
@@ -86,7 +85,7 @@ module heater_block(type, resistor, thermistor) {
 module jhead_hot_end(type, filament) {
     resistor = RIE1212UB5C5R6;
     thermistor = Epcos;
-    heater = type == JHeadMk4 ? MK4_heater : MK5_heater;
+    heater = MK5_heater;
 
     insulator_length = hot_end_insulator_length(type);
     inset = hot_end_inset(type);
@@ -106,7 +105,7 @@ module jhead_hot_end(type, filament) {
 
                     square([hot_end_insulator_diameter(type) / 2 - chamfer, insulator_length]);
                 }
-                square([3.2 / 2, insulator_length]);
+                square([(filament + 0.2) / 2, insulator_length]);
 
                 translate([hot_end_groove_dia(type) / 2, insulator_length - hot_end_inset(type) - hot_end_groove(type)])
                     square([100, hot_end_groove(type)]);
@@ -122,7 +121,7 @@ module jhead_hot_end(type, filament) {
 module jhead_hot_end_assembly(type, filament, naked = false) { //! Assembly with resistor, thermistor, tape, sleaving and ziptie
     resistor = RIE1212UB5C5R6;
     thermistor = Epcos;
-    heater = type == JHeadMk4 ? MK4_heater : MK5_heater;
+    heater = MK5_heater;
 
     insulator_length = hot_end_insulator_length(type);
     inset = hot_end_inset(type);
@@ -139,7 +138,7 @@ module jhead_hot_end_assembly(type, filament, naked = false) { //! Assembly with
     //
     // silcone tape
     //
-    if(!naked)
+    if(is_undef(naked) || !naked)
         color("red")
             if(exploded())
                 translate([0, max(hot_end_insulator_diameter(type) / 2, heater_length(heater) / 2 - nozzle_x(heater)),
@@ -157,7 +156,7 @@ module jhead_hot_end_assembly(type, filament, naked = false) { //! Assembly with
     //
     // Zip tie and heatshrink
     //
-    if(!naked)
+    if(!naked  && !is_undef(naked))
         rotate(10) {
             dia =  hot_end_insulator_diameter(type);
             scale([1, (bundle + dia) / dia])

vitamins/led_meter.scad

@@ -85,7 +85,8 @@ module meter(type, colour = "red", value = "888", display_colour = false) //! Dr
         translate([0, meter_shunt_y(type), size.z])
             vflip()
                 color("#b87333")
-                    wire_link(shunt.y, shunt.x, shunt.z, tail = 2);
+                    not_on_bom()
+                        wire_link(shunt.y, shunt.x, shunt.z, tail = 2);
 }
 
 clearance = 0.1;

vitamins/magnet.scad

@@ -0,0 +1,49 @@
+//
+// NopSCADlib Copyright Chris Palmer 2020
+// nop.head@gmail.com
+// hydraraptor.blogspot.com
+//
+// This file is part of NopSCADlib.
+//
+// NopSCADlib is free software: you can redistribute it and/or modify it under the terms of the
+// GNU General Public License as published by the Free Software Foundation, either version 3 of
+// the License, or (at your option) any later version.
+//
+// NopSCADlib is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;
+// without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+// See the GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License along with NopSCADlib.
+// If not, see <https://www.gnu.org/licenses/>.
+//
+
+//
+//! Cylindrical and ring magnets.
+//
+include <../utils/core/core.scad>
+
+function magnet_od(type)    = type[1]; //! Outer diameter
+function magnet_id(type)    = type[2]; //! Inside diameter if a ring
+function magnet_h(type)     = type[3]; //! Height
+function magnet_r(type)     = type[4]; //! Corner radius
+
+module magnet(type) { //! Draw specified magnet
+    od = magnet_od(type);
+    id = magnet_id(type);
+    h = magnet_h(type);
+    r = magnet_r(type);
+
+    //vitamin(str("magnet(", type[0], "): Magnet ", od, "mm diameter, ", h, "mm high", id ? str(", ", id, "mm bore") : "" ));
+
+    or = od / 2;
+    ir = id / 2;
+    color(silver)
+        rotate_extrude()
+            union() {
+                translate([ir, 0])
+                    rounded_square([or - ir, h], r, center = false);
+                if(!ir)
+                    square([r, h]);
+            }
+
+}

vitamins/magnets.scad

@@ -0,0 +1,30 @@
+//
+// NopSCADlib Copyright Chris Palmer 2020
+// nop.head@gmail.com
+// hydraraptor.blogspot.com
+//
+// This file is part of NopSCADlib.
+//
+// NopSCADlib is free software: you can redistribute it and/or modify it under the terms of the
+// GNU General Public License as published by the Free Software Foundation, either version 3 of
+// the License, or (at your option) any later version.
+//
+// NopSCADlib is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;
+// without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+// See the GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License along with NopSCADlib.
+// If not, see <https://www.gnu.org/licenses/>.
+//
+//
+//! Cylindrical and ring magnets.
+//
+
+//                          od,        id,        h,         r
+MAG8x4x4p2 = ["MAG8x4x4p2", 8,         4.2,       4,         0.5];
+MAG484     = ["MAG484",     inch(1/4), inch(1/8), inch(1/4), 0.5];
+MAG5x8     = ["MAG484",     8,         0,         5,         0.5];
+
+magnets = [MAG8x4x4p2, MAG484, MAG5x8];
+
+use <magnet.scad>

vitamins/opengrab.scad

@@ -25,7 +25,7 @@
 include <../utils/core/core.scad>
 use <../utils/thread.scad>
 
-pitch = 33.8;
+pitch = 33.8 / 2;
 width = 40;
 depth = 18;
 magnet = 4.3;
@@ -37,14 +37,16 @@ pole_l = 36;
 poles = 15;
 
 module opengrab_hole_positions()    //! Position children at the screw positions
-    for(x = [-1, 1], y = [-1, 1])
-        translate([x * pitch / 2, y * pitch / 2, 0])
-            children();
+    let($d = 3.2)
+        for($x = [-pitch, pitch], $y = [-pitch, pitch])
+            translate([$x, $y])
+                children();
 
 module opengrab_side_hole_positions() //! Position children at the two 4mm hole
-    for(side = [-1, 1])
-        translate([side * (width / 2 - 3.5), 0])
-            children();
+    let($d = 4, pitch = width / 2 - 3.5)
+        for($x = [-pitch, pitch])
+            translate([$x, 0])
+                children();
 
 function opengrab_width() = width;              //! Module width
 function opengrab_depth() = depth;              //! Module height
@@ -94,9 +96,9 @@ module opengrab_target() { //! Draw OpenGrab target
                 square([width, width], center = true);
 
                 opengrab_hole_positions()
-                    circle(d = 3.2);
+                    circle(d = $d);
 
                 opengrab_side_hole_positions()
-                    circle(d = 4);
+                    circle(d = $d);
         }
 }

vitamins/pcb.scad

@@ -953,6 +953,7 @@ module pcb_component(comp, cutouts = false, angle = undef) { //! Draw pcb compon
             if(show(comp, "led"))           led(comp[4], comp[5], 2.6);
             if(show(comp, "pdip"))          pdip(comp[4], comp[5], param(6, false), param(7, inch(0.3)));
             if(show(comp, "ax_res"))        ax_res(comp[4], comp[5], param(6, 5), param(7, 0));
+            if(show(comp, "link"))          wire_link(l = comp[4], h = param(5, 1), d = param(6, 0.8), tail = param(7, 3));
             if(show(comp, "D_plug"))        translate_z(d_pcb_offset(comp[4])) d_plug(comp[4], pcb = true);
             if(show(comp, "molex_hdr"))     molex_254(comp[4]);
             if(show(comp, "jst_xh"))        jst_xh_header(jst_xh_header, comp[4], param(5, false), param(6, "white"), param(7, undef));

vitamins/veroboard.scad

@@ -132,8 +132,12 @@ module veroboard(type) { //! Draw specified veroboard with missing tracks and tr
 module vero_components(type, cutouts = false, angle = undef)
     for(comp = vero_components(type))
         vero_grid_pos(type, comp.x, comp.y)
-            translate_z(vero_thickness(type))
-                pcb_component(comp, cutouts, angle);
+            if(comp[3][0] == "-")
+                vflip()
+                    pcb_component(comp, cutouts, angle);
+            else
+                translate_z(vero_thickness(type))
+                    pcb_component(comp, cutouts, angle);
 
 module vero_cutouts(type, angle = undef) vero_components(type, true, angle); //! Make cutouts to clear components